Reiner jetStamp graphic 970 Operating Manua Download

Page: 86 / 94

PCset graphic Help 970

ERNST REINER GmbH & Co. KG

No rechargeable
battery inserted

Device error

Insert the

rechargeable
batteries

Please contact

your specialist
dealer or the
REINER-Support

7.4

Acoustic Signals

Signal

Cause

Removal

Notes

1 sound
impulse

When the trigger button is
pushed while the setting wheel is
in the position

Print images have been deleted

Internal clock battery is empty

Transfer new

print images

Send in device

1 sound
impulse
every 10
seconds

No or defective print cartridge

Wrong print cartridge

Ink level writing error

Print cartridge not inserted
correctly

Rechargeable battery empty

No rechargeable
battery/defective rechargeable
battery

- Print carriage movement

blocked

Insert print

cartridge

Insert print car-

tridge correctly

Charge

rechargeable
battery

Insert/replace

rechargeable
battery

The detailed cause and re-
moval can be determined in
the

status display

of the

PCSet graphic software.

2 sound
impulse
every 10
seconds

Print cartridge almost empty

Check print

3 sound
impulse

Print cartridge empty

Replace print

cartridge

4 sound
impulse

jetStamp graphic

970 not in the

basis station

Put the

jetStamp graphic

970 in the basic
station

The display appears after
30 seconds of non-use in
standard ink, after 10
seconds in MP2 ink and
after 6 seconds in MP3
ink.

Visual signal as well

5 sound
impulses
per minute

Battery nearly flat/capacity low

Charge/replace

rechargeable
battery

Summary of Contents for jetStamp graphic 970































































































Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands

Reiner jetStamp graphic 970, Operating Manua

Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands