manualshive.com logo in svg

Regency Professional Series, Owner'S Manual

Share
Download
Regency Professional Series Owner'S Manual Download Page 14

12

I

NSTALLATION OF

L

IGHT

K

IT

NOTE: Before installing the switch housing to the fan, the light fixture should be installed onto the switch housing.  
1. Remove the plug on the bottom of the switch housing so the light fixture can be connected.  

2. Install the light fixture onto the switch housing and secure it with the lock nut provided.  

3. After installation of the light fixture, connect the wire from the fixture to the switching.  The wires in the switch

housing are marked for LIGHT.  

4. Install the switch housing onto the mounting hub of the fan and secure it with the screws provided.  

After the installation of the switch housing, the globe may be installed.  

5. Install the light bulbs, using the correct wattage per rating.  

6. Install the shade and secure it to the fixture with the mounting hardware provided.  

7. Adjust the glass position so the chain from the switch housing will line up with the hole in the glass and secure.

Summary of Contents for Professional Series


















Reviews:

No comments

Brands by name

Popular brands

Load more brands