Regency Panorama P33CE-LP11 Owners & Installation Manual Download Page 5

Page: 5 / 76

P33CE-11 Direct Vent Gas Fireplace

safety decal

Safety Label

This is a copy of the label that accompanies each P33CE Zero Clearance Direct Vent Gas Fireplace. We have printed a copy of the contents here for your
review. The safety label is located on the front inside base of the unit, visible when the bottom louver is open.

NOTE:

Regency

units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

For the State of Massachusetts, installation and
repair must be done by a plumber or gasfitter
licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, flexible connectors
shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances
individual manual shut-off must be a t-handle
type valve.

The State of Massachusetts requires the installation
of a carbon monoxide alarm in accordance with
NFPA 720 and a CO alarm with battery back up in
the same room where the gas appliance is installed.

Part #: 919-962a

Colour: Black on silver, except for items indicated red.

Size: 9.1” W x 5.7” H (ﬁle at 100%)

Material: 2 ml silver matt polyester (DPM SMS)

Nov 16/18: Created decal
Nov 28/18: Added eﬃciencies

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.

Listed:

VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION

Certified to

/Certifi :

ANSI Z21.88-2017 • CSA-2.33-2017

CSA 2.17-2017

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE

C# 4001172

492

919-962a

NATURAL GAS:

Model P33CE-NG11

PROPANE:

Model P33CE-LP11

Model/Modèle :

P33CE-NG11

Model/Modèle :

P33CE-LP11

APPAREIL FONCTIONNANT AU GAZ NATUREL

Modèle P33CE-NG11

Pression d'alimentation minimale

Pression manifold - lev e

é é

Pression manifold - basse

Taille de l’orifice

D bit calorifique minimal

D bit calorifique maximal

Altitude

APPAREIL FONCTIONNANT AU PROPANE

Modèle P33CE-LP11

Pression d'alimentation minimale

Pression manifold - lev e

é é

Pression manifold - basse

Taille de l’orifice

D bit calorifique minimal

D bit calorifique maximal

Altitude

sé

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 66.49%

Propane Gas / Gaz propane 69.44%

Serial No./ No de série

Minimum Clearances to Combustibles

Dégagements minimaux par rapport aux matériaux combustibles

0’’ Clearance to combustibles from:

Sides, bottom and rear of unit

*Top - 3-1/2’’ (89mm) non-combustible

material required above unit.

Ceiling Clearances from

Top Opening of Unit:

A) 30’’ (762mm)

Side Wall Clearance from

Side Opening of Unit:

B) 9’’ (229mm)

Floor Clearance:

C) 0’’

Alcove Clearances:

D) Min. Width 84’’ (1219mm)

E) Max. Depth 36’’ (914mm)

(See Instruction Manual

for Detailed Instructions)

DOOR SEAL: Please check that

the door is properly sealed

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

Jan. 22/19: Rev. A - remodeled decal and added ETL logo at the bottom

EP5011169

Copy of Safety Decal

Remove the faceplate from unit (refer to manual)
the rating plate will be attached to a black chain
as shown below.

DO NOT REMOVE DECAL FROM UNIT.

Decal Location

Summary of Contents for Panorama P33CE-LP11













































































Search results

Summary of Contents for Panorama P33CE-LP11

Reviews:

Related manuals for Panorama P33CE-LP11

Brands by name

Popular brands

Regency Panorama P33CE-LP11, Owners & Installation Manual

Search results

Summary of Contents for Panorama P33CE-LP11

Reviews:

Related manuals for Panorama P33CE-LP11

Brands by name

Popular brands