background image

Regency

®

 P121/P121LC/P121RC/P131 Zero Clearance Room Sealed Gas Fireplace

16

INSTALLATION 

Diagram 3

Horizontal Flueing with Two (2) 90

o

 Elbows

 

Option 

 V 

  H 

H1

     A) 

1' (305mm) Minimum 

2' (610mm) Maximum

     B) 

2' (610mm) Minimum 

5' (1.5m) Maximum

     C) 

3' (914mm) Minimum 

8' (2.4m) Maximum

     D) 

4' (1.22m) Minimum 

11' (3.35m) Maximum

     E) 

5' (1.5m) Minimum 

14' (4.27m) Maximum

     F) 

6' (1.86m) Minimum 

15' (4.5m) Maximum

Horizontal Flueing with Two (2) 90

o

 Elbows

Option   

          H    

      H + H1

     A) 

1' (305mm) Min.  1' (305mm) Max.  3' (914mm) Max.

     B) 

2' (610mm) Min.  3' (0.91m) Max.  6' (1.86m) Max.

     C) 

3' (914mm) Min.  5' (1.5m) Max. 

9' (2.7m) Max.

     D) 

5' (1.5m) Min. 

8' (2.4m) Max. 

12' (3.6m) Max.

Horizontal Flueing with Three (3) 90

o

 Elbows

Horizontal Flueing with Three (3) 90

o

 Elbows

Diagram 5

Diagram 4

Diagram 6

With the above options, maximum total pipe length if 37 feet with mini-
mum of 6 feet total vertical and maximum 15 feet total horizontal.

Please note minimum 1 foot between 90

o

 elbows is required.

 

Option   

          H    

      H + H1 + H2

 

     A) 

2' (610mm) Min.  1' (305mm) Max.  3' (914mm) Max.

 

     B) 

3' (914mm) Min.  3' (914mm) Max.  6' (1.86m) Max.

 

     C) 

4' (1.22mm) Min.  5' (1.5m) Max. 

9' (2.7m) Max.

 

     D) 

5' (1.5m) Min. 

7' (2.13m) Max.  12' (3.6m) Max.

With the above options, maximum total pipe length if 37 feet with mini-
mum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90

o

 elbows is required.

With the above options, maximum total pipe length if 37 feet with mini-
mum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90

o

 elbows is required.

Option   

V + V1   

 

H + H1

     A) 

2' (610mm) Minimum 

3' (914mm) Maximum

     B) 

3' (914mm) Minimum 

6' (1.86m) Maximum

     C) 

4' (1.22m) Minimum 

9' (2.7m) Maximum

     D) 

5' (1.5m) Minimum 

12' (3.6m) Maximum

With the above options, maximum total pipe length if 37 feet with mini-
mum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90

o

 elbows is required.

Summary of Contents for P121-LPG








































Reviews: