Regency MANSFIELD L850B ST Owners & Installation Manual Download Page 21

Page: 21 / 40

Mansfield L850B ST Woodfire

installation

OPTIONAL FAN KIT INSTALLATION

L850B ST

919-751

12.19.16

OPTIONAL FAN KIT INSTALLATION

NOTE:

Installation of Fan Kit should be done prior

to installation of the wall.

L850B ST Mansfi eld

Mount and secure the fan housing assembly to

framing members, the front of the fan housing will
protrude 12.7mm out of the wall so it may be fi nished
with drywall, etc. See Diagram 2

3. Install the air duct run. Secure the duct to the
duct collar on the unit and the fan housing with 3
screws per end.

Diagram 2: Side View - Secure fan housing

to minimum 45mm framing.

Diagram 1:

Front View

Round Air Duct:

Attach the 152.4mm round air

duct (supplied) to the fireplace collar and run the
duct to the fan housing. Attach the round-to-oval
adapter to the fan housing and the air duct to
the adapter

45mm

Round to Oval

Adapter

Fan Housing

Secure with 3 Screws and

Aluminum Duct Tape at Unit

Air Duct

4. Install the On/Off switch in a convenient

location. This switch controls the fan operation.

NOTE:

Variable speed or Rotary 3 speed switch

(not supplied) can be fi tted.

5. Wire up the the fan, wall switch and power

supply per local codes. See wiring diagram as

reference.

*Electrician to supply wiring

6. Screw fan junction box to the fan housing.

7. Screw the Register Adapter Frame and the

Air Register to the Fan Housing See Diagram 4.

8. Remove the knockout on the top of the unit.

Remove the second knockout, located below

the top knockout.

Diagram 4

12.7mm

45 x 90 mm

9. On the top of the unit, bend the 3 tabs up. Insert

the Duct collar. Secure the collar to the 3 tabs with

screws.

10. The fan duct is now ready to be attached to the

unit. Slide the ducting over the collar and secure

with screws.

11. Final step is to double check the fan ducting

connections at both the unit and fan. Next en-

sure there is a minimum of

25mm clearance to

combustibles.

Strap and secure the fan duct.

Double check the operation of the fan and all

electrical work is completed.

Bend the tabs upwards

Duct collar secured

with screws

Remove the knock out

Summary of Contents for MANSFIELD L850B ST









































Search results

Summary of Contents for MANSFIELD L850B ST

Reviews:

Related manuals for MANSFIELD L850B ST

Brands by name

Popular brands

Regency MANSFIELD L850B ST, Owners & Installation Manual

Search results

Summary of Contents for MANSFIELD L850B ST

Reviews:

Related manuals for MANSFIELD L850B ST

Brands by name

Popular brands