Regency Liberty LRI4E series Owners & Installation Manual Download Page 42

Page: 42 / 72

42 |

LRI4E / HRI4E-11 Direct Vent Gas Insert

installation

919-660

05.18.16

VIGNETTE FACEPLATE

tooltip

1. Pop out tab on right side (facing front) of outer faceplate and place

grommet in opening to route power cord.

2. Install the outer faceplate and secure with 5 screws for the L/HRI4E

and L/HRI6E as shown.

Note: 4 corner screws can be installed on the unit loosely as the hole

on the outer faceplate are keyholes.

Route power cord on right side between the inner and outer profile of

faceplate. Use a grommet and wire clip to secure.

3. Install the Vignette faceplate by hooking the flange over the hanger

as shown.

VIGNETTE FACEPLATE W/ SAFETY SCREEN INSTALLATION

Final Install

Note:

Shown with Optional Hearth Trim

4. Ensure finger prints or smudges are removed from the faceplate

before the first firing.

NOTE: Pull the bottom of the Vignette faceplate towards you to access

the remote receiver.

Power Cord

Location

Pop out tab on right side

of outer faceplate

Black Chrome Handling Instructions

All hand and finger marks

MUST

be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any

finger prints before applying heat to the unit. Use supplied gloves when installing Black Chrome Faceplates.

Failure to do this will result in burn stains on panels which you will be unable to remove.

Not protected by product warranty.

tooltip

VIGNETTE FACEPLATE WITH SAFETY SCREEN INSTALLATION

Summary of Contents for Liberty LRI4E series









































































Search results

Summary of Contents for Liberty LRI4E series

Reviews:

Related manuals for Liberty LRI4E series

Brands by name

Popular brands

Regency Liberty LRI4E series, Owners & Installation Manual

Search results

Summary of Contents for Liberty LRI4E series

Reviews:

Related manuals for Liberty LRI4E series

Brands by name

Popular brands