Regency Horizon HZ42E-LP Owners & Installation Manual Download Page 18

Page: 18 / 60

HZ42E Regency Horizon™ Gas Fireplace

INSTALLATION

EXTERIOR VENT TERMINATION REQUIREMENTS

Minimum Clearance Requirements

Canada

USA

Clearance above grade, veranda, porch, deck, or balcony

12"(30cm)

Clearance to window or door that may be opened

12"(30cm)

9" (23cm)

Clearance to permanently closed window

Vertical clearance to ventilated soffi t located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)

19"(48cm)

Clearance to unventilated soffi t

19"(48cm)

Clearance to outside corner: with

AstroCap

Termination Cap.

7"(18cm)

Clearance to outside corner: with all other approved Termination Caps.

13"(33cm)

Clearance to inside corner: with

AstroCap

Termination Cap

7"(18cm)

Clearance to inside corner: with all other approved Termination Caps.

13"(33cm)

Clearance to each side of center line extended above meter/regulator assembly

36"(90cm)

Clearance to service regulator vent outlet

36"(90cm)

Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance

12"(30cm)

9" (23cm)

Clearance to a mechanical air supply inlet

#3' (91cm) above if within 10' (3m) horizontally.

72"(1.8m)

36"(90cm)

Clearance above paved sidewalk or a paved driveway located on public property

84"(2.1m)

┼

Clearance under veranda, porch, deck, or balcony

12"(30cm)

‡

In accordance with current CSA B149.1,

Natural Gas and Propane Installation Code

In accordance with the current

ANSI Z223.1/NFPA 54, National Fuel Gas Code

┼

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the fl oor

* Clearance in accordance with local installation codes and the requirements of the gas supplier

3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly

3 feet (91cm) above - if within 10 feet (3m) horizontally

Summary of Contents for Horizon HZ42E-LP





























































Search results

Summary of Contents for Horizon HZ42E-LP

Reviews:

Related manuals for Horizon HZ42E-LP

Brands by name

Popular brands

Regency Horizon HZ42E-LP, Owners & Installation Manual

Search results

Summary of Contents for Horizon HZ42E-LP

Reviews:

Related manuals for Horizon HZ42E-LP

Brands by name

Popular brands