Regency Horizon HZ42E-LP Owners & Installation Manual Download Page 1

Page: 1 / 60

WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.

FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.

FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:

do not use any phone in your
building.

Immediately call your gas supplier

from a neighbour's phone. Follow
the gas supplier's instructions.

If you cannot reach your gas

supplier, call the fi re department.

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

918-932

Regency Horizon™ HZ42E

Gas Fireplace

06/25/13

Owners &

Installation Manual

www.regency-fi re.com

Tested by:

Installer

Installer: Please complete the details on the back cover

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

MODELS: HZ

42E-NG Natural Gas

42E-LP Propane

Summary of Contents for Horizon HZ42E-LP





























































Search results

Summary of Contents for Horizon HZ42E-LP

Reviews:

Related manuals for Horizon HZ42E-LP

Brands by name

Popular brands

Regency Horizon HZ42E-LP, Owners & Installation Manual

Search results

Summary of Contents for Horizon HZ42E-LP

Reviews:

Related manuals for Horizon HZ42E-LP

Brands by name

Popular brands