background image

4

U32-5 FPI Direct Vent Gas Insert

4

TABLE OF CONTENTS

OPERATING INSTRUCTIONS

Operating Instructions  ................................................32
Lighting Procedure ......................................................32
Shutdown Procedure ...................................................32
First Fire ......................................................................32
Automatic  Convection Fan Operation.........................32
Normal Operating Sounds Of Gas Appliances ............32

MAINTENANCE

Maintenance  Instructions............................................33
Copy Of Lighting Instruction Plate ...............................33
General Vent Maintenance ..........................................34
Log Replacement ........................................................34
Glass Gasket ...............................................................34
Gold-plated Trim ..........................................................34
Door Glass ..................................................................34
Fan Maintenance .........................................................35
Valve Replacement ......................................................36

PARTS LIST

Main Assembly ............................................................37
Burner Assembly & Log Set.........................................38
Flush Front Assembly ..................................................39
Faceplate Assembly ....................................................40
Contemporary faceplate and doorframe ......................41
Low pro

fi

 le faceplate ...................................................42

WARRANTY

Warranty ......................................................................43

SAFETY LABEL

Copy of the Safety Label ...............................................5

REQUIREMENTS

MA Code - CO Detector.................................................6
(for the State of Massachusetts only) ............................6

INSTALLATION

Important Message   ......................................................8
For Your Safety ..............................................................8
Speci

fi

 cations ................................................................8

Gas Pressure Testing ....................................................8
Installation Into A Solid Fuel Burning Fireplace Or 
Factory Built Fireplace ...................................................8
Before You Start ............................................................8
Installation Checklist ......................................................9
Manufactured Mobile Home Additional Requirements ..9
Materials Required ........................................................9
Minimum Fireplace Dimensions ....................................9
Clearances To Combustibles .........................................9
Gas Connection  ..........................................................10
Venting.........................................................................10
Flue Liner Installation ..................................................10
Gas Pipe Pressure Testing .......................................... 11
Gas Insert Aeration System ......................................... 11
Optional Brick Panel .................................................... 11
Log Set Installation ......................................................12
Regency Faceplate & Trim Installation ........................16
Standard Flush Door ...................................................17
Flush Louvers ..............................................................17
Conversion from NG to LP   ........................................18
Full Screen doors ........................................................21
Contemporary Faceplate & doorframe installation ......23
Optional hearth trim installation ...................................25
Low pro

fi

 le Faceplate  installation ...............................26

Low pro

fi

 le hearth trim .................................................28

Optional Wall Thermostat  ...........................................29
Optional Remote Control  ............................................29
Final Check..................................................................29
Wiring Diagrams ..........................................................30

Summary of Contents for energy U32













































Reviews: