Regency E21-LP2 Owners & Installation Manual Download | Manualshive

Page: 20 / 32

background image

20

Regency

®

E21-2 Gas Fireplace Insert

FULL SCREEN DOORS

1)

Hold the full screen door up against the unit in order to make the

following wire connections.

Pull the ON/OFF connector wires thru the box and connect them to
the switch.

Connect the fan switch wires with the wire connectors from the fan
speed control. Place clips over wires and tuck into side trim.

2)

Lift the unit up slightly and push down on the corners of the Bottom

Trim Bracket and slide under unit.

Bottom Trim

Bracket

Push in Corners

3)

Completely secure full screen door to the unit by securing 4 screws

to the Left and Right Side Trim.

4)

Secure the Top Frame by sliding it on the screws at the top of the full
screen door. It is held in place by magnets.

Top Frame

Screw

INSTALLATION

«
...
18
19
20
21
22
...
»

Summary of Contents for E21-LP2

































Reviews:

No comments

Related manuals for E21-LP2

Brand: Napoleon Pages: 2

Brand: Cannon Pages: 38

Siena Fire SNA20

Brand: Dimplex Pages: 3

Valor Legend Ultra 837 AN

Brand: Valor Pages: 12

Ascent Multi-View Series

Brand: Napoleon Pages: 70

Brand: Jeco Pages: 3

Pro Builder 72 Linear GSB2

Brand: Lopi Pages: 68

Brand: Sunjoy Pages: 4

Brand: Napoleon Pages: 120

Brand: Majestic Pages: 56

Brand: Twin-Star International Pages: 28

Fire Ribbon Direct VEnt Slim 26"

Brand: Spark Pages: 48

MODEL OSBURN STRATFORD

Brand: Stove Builder International Pages: 38

Brand: Lennox Pages: 40

RUTHERFORD 36-B

Brand: Heat & Glo Pages: 54

Brand: Essence Pages: 3

Brand: Dimplex Pages: 15

Brand: Heat & Glo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands