Regency City CC40LEPV-LP Owners & Installation Manual Download Page 25

Page: 25 / 88

City Series CC40EPV

| 25

installation

Caution Requirements

The top, back and sides of the fireplace are defined by

standoffs. The metal ends of the standoff may

NOT be

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this fireplace and vent

system be installed only in accordance with these instructions.

Clearances CC40LE/CC40RE

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and vent system be installed only in accordance with these instructions.

Note: CC40LE shown in illustration. Clearances will be the same for the CC40RE.

Clearance: single sided

Dimension

Measured From:

A: Mantel Height (min.)

Top of Fireplace Opening

B: Opening Height

15-1/16" (382mm)

Bottom/Top of Fireplace Opening

C: From Floor

Min. 0"

Bottom of Fireplace Opening

D: Sidewall (on one side)

Min. 36" (914mm)

Side of Fireplace Opening

E: Mantel Depth (Max.)

Front of Fireplace Opening

F: Alcove Depth

Min. 36" (914mm)

Front of Fireplace Opening

G: Convection Air Outlet

Top of Enclosure

H: Convection Air Outlet Opening Offset

0-3" (76mm)

Max. offset from top of chase enclosure

I: Chase Enclosure (Min.)

63" (1600mm)

From Base of Unit

Hearth

No hearth required

See mantel clearances chart in this manual.

Flue Clearances to Combustibles

Horizontal - Top

Horizontal - Side

Horizontal - Bottom

Vertical

Passing through wall/
floor/ceiling - when
firestop is used.

1-1/2"

Top View

Alcove

The

HeatWave Duct Kit has differ-

ent clearance and framing require-
ments, check the

HeatWave manual

for details.

A minimum of 120 square

inches of open area, not
lower than 3" from top of
enclosure, required for all
installations

CC40 UNIT

Summary of Contents for City CC40LEPV-LP

























































































Search results

Summary of Contents for City CC40LEPV-LP

Reviews:

Related manuals for City CC40LEPV-LP

Brands by name

Popular brands

Regency City CC40LEPV-LP, Owners & Installation Manual

Search results

Summary of Contents for City CC40LEPV-LP

Reviews:

Related manuals for City CC40LEPV-LP

Brands by name

Popular brands