Regency CB40E-LP11 Owners & Installation Manual Download Page 19 | Manualshive

Page: 19 / 88

background image

CV40E-11 City Series

|

19

requirements

installer's information

Locating Your
Gas Fireplace

1. When selecting a location for your fireplace,

ensure that the clearances are met.

2. The appliance must be installed on a flat, solid,

continuous surface For example a wood, metal
or concrete floor or in a raised (on the wall) ap-
plication. The appliance must be installed on
a metal or wood panel extending the full width
and depth of the appliance.

3. The CV40E Direct Vent Gas Fireplace can be

installed in a recessed position or framed out
into the room as in A, B, C, D.

See Diagram 1.

E

Diagram 1

CV40E

A)

Flat on Wall-CV40E

B)

Flat on Wall Corner-CV40E

C)

Recessed into Wall/Alcove-CV40E

D)

Corner-CV40E

4. For bedroom installations, check with local

codes before installation. This appliance is
offered with a remote control.

5. The CV40E Direct Vent Gas Fireplace is ap-

proved for alcove installations, see "Clearances"
section for details.

6. We recommend that you plan your installa-

tion on paper using exact measurements for
clearances and floor protection before actually
installing this appliance. Have an authorized
inspector, dealer, or installer review your plans
before installation.

Note:

For vent terminations refer to "Exterior
Vent Termination Locations" section.

Unit Assembly Prior to Installation

Before you start

The CV40E has 6 standoffs, 2 on each side and 2 at the back that need assembly before installation.

WARNING!

Risk of Fire! Comply with all minimum clearances.

Side and Back Standoff Assembly CV40E

The standoffs are shipped in a flat position and must be folded into shape and attached.

Take each standoff off the unit by removing one screw and bend into the correct shape. Slot the 2 tabs
of the stand off into the slots in the unit and attach the other end with one screw.

Standoﬀ

locations

Nailing Strips CV40E

Nailing strips are shipped folded flat against the unit.
Fold nailing strips out 90º before installing unit.
Secure nailing strips to framing using wood or
metal screws.

Nailing

strips

«
...
17
18
19
20
21
...
»

Summary of Contents for CB40E-LP11

























































































Reviews:

No comments

Related manuals for CB40E-LP11

Brand: IHP Pages: 8

Legend G3 738 NGK

Brand: Valor Pages: 6

Brand: Majestic Pages: 44

Brand: Valor Pages: 29

Brand: Ravelli Pages: 9

Brand: HAMPTON BAY Pages: 17

Edge HCLC/P/L1100

Brand: Horizon Fireplaces Pages: 22

Brand: Majestic Pages: 29

FP-7-LM ANTOINETTE

Brand: Valcourt Pages: 2

Brand: Majestic Pages: 36

Brand: Viessmann Pages: 4

Brand: Lopi Pages: 40

Brand: Lopi Pages: 15

864 TRV 31K CleanFace

Brand: Lopi Pages: 60

Brand: hergom Pages: 64

Brand: hergom Pages: 40

Brand: Cotech Pages: 5

Brand: Costway Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands