background image

10

     | 

F2450M Regency Freestanding Woodstove

installation

Floor Protection
(Ember Protection only required)

A combustible floor must be protected by a non-combustible material (like tile, concrete board, or 
certified to UL-1618 Type 1, or as defined by local codes). 

Canada:  Beneath the heater and extending to at least 18" on the fuel loading side and at least 8" 

on the sides and back.

USA:  Beneath the heater and extending to at least 16" beyond the fuel loading side and ash removal 

opening and at least 8" on the sides and back and under the chimney connector extending 2" 
beyond each side for horizontal applications.

 Minimum Overall Depth (Y) of Floor Protector
Reference only when hearth pad is installed to 
rear wall at minimum pipe clearances.

Hearth
Depth

Edge of Fuel door 
opening to edge of 
hearth

Hearth
Width

Edge of Fuel Door Opening
(Both Sides)

Residential Installation ''C'' Vent (Single Wall)

Unit

A

B

C

D

F2450M with Airmate

Canada

50-1/2" (1283mm)

18" (457mm)

33-11/16" (856mm)

8" (203mm)

USA

48-1/2" (1232mm)

16" (406mm)

33-11/16" (856mm)

8" (203mm)

F2450M with Rear
Deflector

Canada

52-1/2" (1334mm)

18" (457mm)

33-11/16" (856mm)

8" (203mm)

USA

50-1/2" (1283mm)

16" (406mm)

33-11/16" (856mm)

8" (203mm)

Residential Close Clearance (To be installed with required pipe components)

Unit

A

B

C

D

F2450M with Airmate

Canada

48" (1219mm)

18" (457mm)

33-11/16" (856mm)

8" (203mm)

USA

46" (1168mm)

16" (406mm)

33-11/16" (856mm)

8" (203mm)

F2450M with Rear
Deflector

Canada

50" (1270mm)

18" (457mm)

33-11/16" (856mm)

8" (203mm)

USA

48" (1219mm)

16" (406mm)

33-11/16" (856mm)

8" (203mm)

C

B

D

A

D

Minimum Alcove Clearance and Clearance to Combustible Materials

The Regency Freestanding models have been alcove approved and must be installed 
with a listed double wall connector to the ceiling level. 

Note:  Minimum alcove ceiling height - 83"
 

  Maximum depth of alcove - 48"

G

K

16"

405mm

H

J

I

NOTE: 

This clearance is also required for air space between the appliance and wall/ceiling. Where the 

appliance is installed less than 8" from a rear wall, the ember pad only needs to extend to the base of 
the wall based on the clearances noted in this manual.

Unit

From Unit

From Flue Center-Line

From Wall

G

H

I

J

K

Medium F2450M         with Airmate   

15" (381mm)

 8" (203mm)

 27" (686mm)

14.5" (368mm)   54" (1372mm) 

 

 with Rear Deflector

  15" (381mm)

 10" (254mm) 

 27" (686mm)

16.5" (419mm)  54" (1372mm) 

 

Minimum Overall Depth (Y) of Floor Protector

Edge  of  Fuel  door 
opening to edge of 
hearth

Edge  of  Fuel  Door 
O p e n i n g   ( B o t h 
Sides)

Unit

A

                          

B

                                      

C

                        

D

F2450M Canada 49" (1245mm)

18" (457mm)

33 11/16" (856 mm)  8" (203mm)

USA

47" (1194mm)

16" (406mm)

33 11/16" (856 mm)  8" (203mm)

Summary of Contents for Cassic F2450













































Reviews: