L390E / HZI390E Direct Vent Gas Insert
33
installation
GLASS dOOR REmOVAL / INSTALLATION
Upper Door Hooks
Lower Door Latches
Door Attachment Point
2)
Pull forward until the lower door latch is disengaged from the door frame.
3)
Push downward until the Lower Door Latch is below the Door Frame.
4)
Release the lower door latch until it reaches its resting point.
5)
Remove the door tool and repeat steps 1-5 on the other lower door latch.
6)
Pull the bottom of the door towards you until the door is angled away from
the firebox by about 30
°.
Lift the door up and over the upper door hooks.
7)
To install the glass door - reverse steps.
Door Components
Window Glass
Window Glass Gasket
Door Frame
Window Clip (x4)
Glass Gasket Retainer
1)
Insert the door tool into the lower door latch.
WARNING: do not operate the appliance
with the glass panels removed, cracked or
broken. Replacement of the glass panels
should be done by a licensed or qualified
service person.
Door Tool
919-025
11/07/11
1
L390E / HZI390E / HZI540EB /L540EB
ENAMEL PANEL INSTALLATION
Porcelain Liner Right
Insulation Panel Side (x2)
Porcelain Liner Rear
Insulation Panel Rear
Porcelain Panel Left
Firebox Liner
Retainers
Sheet metal components may have sharp edges. Please handle with
care. The enamel panels require an insulation panel installed behind
them. Failure to do so may result in an elevated operating temperature
and premature failure of the appliance. The Insulation panels may contain
fi bre glass or ceramic elements. These may become airborne or stick to
carpets and/or clothing. Handle with caution.
The use of work gloves and dust masks is recommended when handling
panels and insulation.
2)
Using a screw driver, loosen the screws that hold down the Firebox Liner
Retainers (x4). Move the Firebox Liner Retainers toward the center of the
Firebox.
3)
Place the insulation panels on the inside of their respective fi rebox liners.
Have both the rear liner and the right liner within reach of the Firebox.
The rear liner has one long edge with perpendicular lip and one long
edge with a lip angled downward. The angled lip is the top of the panel.
The liner sits on a sheet metal ledge at the rear of the fi rebox, just above
the air inlet near the bottom.
While holding the rear liner in place, slide the fi rebox liner right (and the
corresponding insulation panel) into the right side of the Firebox. The side
liners will sit on the fi rebox liner retainers and fi t at the top in-between the
fi rebox side and the exhaust baffl e. The rear fl ange on the Firebox Liner
Side, sits between the rear liner and the fi rebox side. When the side liner
is properly installed, the front edge should sit just inside the front edge of
the fi rebox.
Interlocking of the
side and rear Firebox
Liners
Insulation Panels
Firebox
Liner Rear
Side and Rear Panel
Positioning
Bottom Right of Firebox
Firebox Liner Retainers
Exhuast Baffle
Top Right of Firebox
4)
Install the fi rebox liner Left, with the corresponding Insulation Panel by
sliding it into the left side of the fi rebox. The rear fl ange of the liner must
fi t between the fi rebox liner rear and the fi rebox. You may have to push
the liner against the fi rebox as you push it rearward.
5)
Push the fi rebox liner retainers against the panels, pushing the panels
tight against the fi rebox sides. Secure the screws that hold down the
fi rebox liner retainers (x4).
6)
Reinstall burner.
1a)
(L390E/L390EB/HZI390E/HZI390EB only)
Remove fi ller sections from right and left sides of burner and
discard - see below.
( L540EB/HZI540EB only)
Remove metallic black left and right side inner panels by sliding
them forward - see below. Discard panels after removal
b)
Remove burner. See glass crystal burner removal section in manual.
Filler section
L390E/L390EB
Before you Start:
Black Enamel Panels
• Black Enamel panels must be inspected for scratches and dimples
prior to installation. All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.
• Black Enamel panels will discolor a little during normal operation. This
is normal and should not be considered a defect.
*
All hand and fi nger marks
MUST
be cleaned off with a soft cloth. Use
an ammonia based cleaner (ie. glass cleaner) to remove any fi ngerprints
before applying heat to the unit.
Failure to do this will result in burn stains on panels which you
will be unable to remove.
Not protected by product warranty.
