SP 1-Ex
29
Legend:
Z10b............wiring diagram of resistive with current converter or capacitive transmitter – 2 - wire without supply
Z22..............wiring diagram of single resistant transmitter connection
Z32..............wiring diagram of double resistant transmitter
Z248............wiring diagram of EA SP 1-Ex with controller with current feedback - 230 V AC
Z249a..........wiring diagram of EA SP 1-Ex with controller with resistant feedback - 230 V AC
Z257d..........3-wire version of EPV - without power supply connection
Z260c ..........wiring diagram of resistive transmitter with current converter -3-wire version with power supply
Z269b..........wiring diagram of resistive transmitter with current converter or capacitive transmitter -2-wire version
with power supply
Z525............wiring diagram of electric motor 24 V DC
Z524............wiring diagram of EA with electric motor 24 V AC
Z521d..........wiring diagram of SP1- Ex with controller and resistant feedback for electric motor – for 24 V AC
Z522d..........wiring diagram of SP1- Ex with controller and current feedback for electric motor – for 24 V AC
Z519d..........wiring diagram of SP1- Ex with controller and resistant feedback for electric motor – for 24 V DC
Z520d..........wiring diagram of SP1- Ex with controller and current feedback for electric motor – for 24 V DC
Z378a..........wiring diagram of resistive with current converter or capacitive transmitter 2 and 3 - wire with supply
Z395............wiring diagram of position switches for 3-phase electric motor
Z396............wiring diagram of thrust switches for 3-phase electric motor
Z397............connection of 3-phase electric motor with terminated thermal protection.
Z397a.......... connection of 3-phase electric motor with build in thermal protection
Z398............connection of position switches - terminated release contacts - for version with 3-phase electric
motor
Z491, Z491g.... wiring diagram of EA with electric motor 230 V AC
Z479............wiring diagram of switches S1 – S4
B1 ............ single resistant transmitter
B2............. double resistant transmitter
B3............. capacitive transmitter, or EPV
E1 ............ space heater
F1 ............ electric motor thermal protection
F2 ............ space heater thermal switch
I/U ............ input (output) current (voltage) signals
M ............. electric motor
C ............. capacitor
N .............. position controller
R .............. voltage-dropping resistor (for 230V only)
S1 ........... thrust switch "open"
S2 ........... thrust switch "closed"
S3 ........... position switch "open"
S4 ........... position switch "closed"
S5 ........... additional position switch "open"
S6 ........... additional position switch "closed"
X ............. terminal board
Y............... brake of electric moto
1. In case, that output signal from the capacitive transmitter (wiring diagram Z248, Z520d,Z522d) is not used
(incomplete circuit between terminal 81 and 82), it is required to connect clamps 81 and 82 by jumper (jumper is
connected at manufacturing plant for connecting to terminal board only). By using output current signal from
capacitive transmitter it is needed to remove jumper.
2. In the version equipped with the controller device while using the feedback from transducer CPT; when using
the output signal there has been no galvanic isolation of the signal from the input one!
3. In case that galvanically separated output signal is needed it is necessary to use galvanical separation
element (is not part of delivery), e.g. NMLSG.U07/B (producer SAMO Automation s.r.o.). After discussion this
module could be supplied by EA producer.
4. Wiring diagram Z525 without switch S6 is version with single resistant transmitter connection and 3 – wire
converter without power supply. Wiring diagram Z525 without switch S5, S6 is version with double resistant
transmitter.
5. Wiring diagram Z524 without switch S6 is version with any position transmitter. Wiring diagram Z524 without
switch S5, S6 is version with double resistant transmitter.
6. Wiring diagram Z491 without switch S6 is version with optional position transmitter. Wiring diagram Z491
without switch S5, S6 is version with single resistant transmitter and 3 – wire converter without power supply.
Summary of Contents for SP 1-Ex
Page 28: ...26 SP 1 Ex 7 Enclosures 7 1 Wiring diagrams Wiring diagrams EA SP 1 Ex...
Page 29: ...SP 1 Ex 27 Wiring diagrams EA SP 1 Ex with controller ERROR MESSAGE ERROR MESSAGE...
Page 30: ...28 SP 1 Ex...
Page 33: ...SP 1 Ex 31 7 2 Dimensional drawings 7 2 1 Dimensional drawings flange connection Flange...
