Commissioning
Variomat Basic
—
22.07.2020 - Rev.
A
English
—
19
Indication on
the display
Meaning
Customer menu Switch to the next main menu option.
Language
Standard software in various languages.
Time:
Adjust the "Hour", "Minute", and "Second" display
when each begins to flash.
This time is used for entries in the fault memory.
Date:
Adjust the "Day", "Month", and "Year" display
when each begins to flash.
This date is used for entries in the fault memory.
1 % / 1.7 bar
Null balancing
successfully
concluded!
The controller checks whether the level sensor
signal matches the value entered for the "VG"
primary tank in the controller, see chapter 8.3
"Modifying the controller's start routine" on
page 17 .
Note!
The "VG" primary tank must be completely
empty.
0 % / 0 bar
XXX XXX XXX
XXX
One of the following messages appears on the
display:
•
Null balancing concluded successfully
Confirm with the "
▼
" button.
•
Empty the tank and repeat the process
Confirm with "OK".
0 % / 0 bar
Cancel null
balancing?
No
This message appears when null balancing has
failed. Select "Yes" or "No" on the display.
•
YES:
The "VG" primary tank is empty and the
device is installed as per the instructions. If
null balancing is still not possible, cancel with
"Yes". Contact your Reflex Customer Service.
•
NO:
Check the prerequisites for the
commissioning, see chapter 8.1 "Checking the
requirements for commissioning" on page 16 .
Confirm the selection of "yes" or "no" with "OK".
Min.op.pressure
01.8 bar
Enter the value for the minimum operating
pressure.
Note!
Calculation of minimum operating pressure,
see chapter 9.1 "Automatic mode" on
page 20 .
Degassing
˃
Switch to the "Degassing" sub-menu.
•
Press "OK" to open the menu.
•
Use the "
▼▲
" buttons to open the next sub-
menu.
Degassing
Switch to the next list item.
Degassing
programme
Interval
degassing
Select between the degassing programmes:
•
Continuous degassing
•
Interval degassing
For a detailed description, see chapter 8.3
"Modifying the controller's start routine" on
page 17 .
Indication on
the display
Meaning
Time
Continuous.
degas.
12 h
Time setting for Continuous degassing.
The standard values during commissioning can be
between 12 and 100 hours. The default setting is 12
hours.
Less times for continuous degassing are sufficient
when the following conditions apply:
•
Significant gauge pressure (≥ 0.5 bar above
atmospheric pressure) at the high point.
•
Little difference between the maximum
temperature at the high point and the
degassing temperature.
•
Small system volume with low initial gas
content due to good initial ventilation, for
example.
Make-up
Switch to the "Make-up" sub-menu.
•
Press "OK" to open the menu.
•
Use the "
▼▲
" buttons to open the sub-
menu.
If the water content is below the specified tank
size, add water, see chapter 4.6 "Optional
equipment and accessories" on page 5 .
•
If an automatic make-up device (Fillcontrol for
example) is installed, make-up will be
actuated automatically; otherwise the make-
up must be manually activated.
Terminate the water make-up when the specified
tank size is exceeded.
•
If an automatic make-up device is installed,
make-up will be shut off automatically;
otherwise the make-up must be manually
deactivated.
•
If you have selected "No" for automatic make-
up, the system will not return any further
queries about the make-up.
Max. make-up
time
010 min.
Pre-selected time for a make-up cycle. Upon
expiry of this set time, the system interrupts the
make-up and returns the "Make-up time" fault
message.
Max. make-up
cycles
003 / 2 h
If the set number of make-up cycles is exceeded
within two hours, the system interrupts the make-
up and returns the "Make-up cycles" fault
message.
With water
meter.
YES
•
YES:
FQIRA+ contact water meter is installed,
see chapter 10.3 "Messages" on page 22 .
This is the prerequisite for the make-up
quantity monitoring and the operation of a
softening system.
•
NO:
A contact water meter is not installed
(standard model).
Make-up quantity
000020 l
Only displayed if "YES" has been set in the "With
water meter" menu option.
•
Use "OK" to delete the counter.
–
Press "
YES
" to reset the value displayed
to "0".
–
Press "
NO
" to retain the displayed
value.
Max. make-up
quantity
000100 l
This value is only displayed if "YES" has been set in
the "With water meter" menu option.
•
When the set quantity is exceeded, the
system interrupts the make-up process and
returns the error message "Max. make-up
quantity exceeded".
