background image

CAUTION!

 

Read, understand and follow all warnings and instructions before using this product. Failure to follow 
these directions may result in property damage, serious bodily injury, and/or death.

 

Cequent 

Consumer Products is not responsible for any property damage, personal injury, or death occurred 
while using any Reese Carry Power products.

 

Retain these instructions for future reference.

 

WARNING!

 

Do not exceed the lesser of the maximum load capacity of 800 lbs. (evenly distributed) or the vehicle 
manufacturer’s specified load capacity for rail mounted accessories. “Distributed load” is defined as a 
load that is not concentrated in a small area. 

Any load carried above the bed rails will increase your truck’s center of gravity and will significantly 
hinder your trucks ability to maneuver, stop turn or accelerate. Avoid sharp turns and excessive speeds as 
this will increase risks. 

This truck rack is solely intended for, and only safe for, transporting ladders, lumber, pipe and other 
similar materials or recreational items such as canoes and kayaks. 

Ladder damage will occur from road shock and vehicle vibration if the ladder is not properly secured to 
the rack. The bouncing side to side motion of an improperly secured ladder will cause wear and weaken 
the ladder. Using a damaged ladder could lead to a structural collapse and could result in a serious injury 
or death. 

Any modification or unintended use of this product voids any warranty and could create a hazardous 
condition that may result in property damage, serious bodily injury and/or death. The sole exception being 
permanent mounting within the prescribed method. 

Always secure long loads to front and rear of vehicle for safe transport. 

Do not use in truck beds that have excessive rust as it may decrease the capacity and result in product  
and/or bed failure. 

Truck beds with liners may require modification prior to use of the product. 

The installation and use of any rail mounted accessory may cause minor aesthetic damage to the vehicle 
exterior. Cequent Consumer Products makes no claims or warrantees whatsoever as to a particular 
vehicle’s ability to support rail mounted accessories without incurring damage. 

IMPORTANT! 

 

Loads that exceed the vehicle manufacturer cargo and / or entire gross vehicle weight (GVW) rating, are 
not covered by this warranty. 

Consult and follow your vehicle manual for capacity ratings. 

Always evenly distribute load on rack before driving. 

Loads must be secure according to local height and identification regulations and or laws. 

Secured loads and connections must be re-checked periodically for tightness. 

Overloading the vehicles GVW may cause damage and severely alter the vehicle’s handling and braking 
characteristics and or cause the vehicle to roll over. 

It is recommended the tailgate be in the up position during use to better stabilize the truck bed. 

Always obey posted speed limits and traffic cautions. 

Lubricate with an anti-seize lubricant for best long term performance of stainless steel hardware. 

Failure to follow these warnings or instructions will void the warranty. 

Some vehicle manufacturers require a reinforcing kit. Contact your dealership for details. 

The TransRACK rail kit is based on vehicle design available at the revision of these instructions. The 
TransRACK top rail kit is designed to fit a variety of bed lengths and cab designs.  

Summary of Contents for TransRACK 70552









Reviews: