Reefe 21620 Exploded View & Instruction Manual Download Page 3

www.

reefe

.com.au

Ascento Group Australia

© 

AI.062020

P: 1800 807 604

 

P U M P S   A U S T R A L I A

BETTER • FASTER • EASIER

BETTER • FASTER • EASIER

INSTRUCTION | 

INSTALLATION MANUAL

MINIMUM 
50MM

CORRECT  INSTALLATIONS

INCORRECT  INSTALLATIONS

(1)  BARREL UNION

(2) Y-STRAINER OR PRE-FILTER

(3) BALL VALVE OR GATE VALVE

KEY

ALWAYS INSTALL YOUR PUMP ON A LEVEL CONCRETE OR PAVED SURFACE!

DIAGRAM 1

INCORRECT! 

PUMP IS INSTALLED 

WITHOUT BARREL UNION’S, A 

Y-STRAINER & A BALL VALVE.

!

WRONG!

DIAGRAM 3

DIAGRAM 4

TIP!

 CLEAN THE Y-STRAINER MONTHLY TO  ENSURE PEAK PERFORMANCE. 

SIMPLY UNDO THE BUNG AND LET IT FLUSH OUT. MAKE SURE YOU RE-FIT THE 

MESH FILTER.

TIP!

 IF PUMP STARTS FREQUENTLY, CHECK TOILET CISTERNS, THEY ARE 

PROBABLY LEAKING. 

PRESSURE TANKS 

CAN SAVE YOU 

MONEY AS THE 

PUMP DOES NOT 

HAVE TO START SO 

OFTEN.

TIP!

IMPORTANT! MULTISTAGE PUMPS MUST NOT BE USED WITH SUCTION LIFT.

INCORRECT!

PUMP IS 

INSTALLED 

WITHOUT A 

CHECKVALVE OR 

A FOOT VALVE.

!

WRONG!

VSRE - Parts Breakdown.indd   3

VSRE - Parts Breakdown.indd   3

25/06/2021   1:32:51 PM

25/06/2021   1:32:51 PM

Summary of Contents for 21620











Reviews: