REED ST-333 Instruction Manual Download Page 6

reedinstruments

www

com

6

Function 

Range & Resolution

Accuracy (% of reading)

Capacitance

40.00nF

±(5.0% r 10 digits)

400.0nF

±(3.0% r 5 digits)

4.000μF

±(3.5% r 5 digits)

40.00μF
100.0μF

±(5.0% r 5 digits)

Frequency

5.000Hz

±(1.5% r 5 digits)

50.00Hz

±(1.2% r 2 digits)

Sensitivity: 5~5kHz:10Vrms min.

5kHz~150kHz:40Vrms min.

 @ 20% to 80% duty cycle

500.0Hz

5.000kHz
50.00kHz
150.0kHz

Duty Cycle

0.5 to 99.0%

±(1.2% r 2 digits)

Pulse width: 100μs - 100ms, Frequency: 5Hz to 150kHz

Sensitivity: 5~5kHz:10Vrms min.5kHz~150kHz:40Vrms min.

 @ 20% to 80% duty cycle

Temp (type-K) 

(probe accuracy 

not included)

-50.0 to 400.0°C

-50.0 to -20.0°C

± 7°C

-20.0 to 400.0°C

±(3.0% r 5 °C)

400 to 1300°C

400 to 1000°C

1000 to1300°C

±(3.0% r 5°C)

-58.0 to 400.0°F

-50.0 to 0°F

± 14°F

0 to 400.0°F

±(3.0% r 7°F)

400 to 2372°F

400 to 1832°F

1000 to1300°F

±(3.0% r 10°F)

Clamp Size 

Opening 0.9” (23mm) approx

Diode Test 

Test current of 0.3mA typical; 

 

 

Open circuit voltage 1.5V DC typical

Continuity Check 

Threshold <100Ω; Test current < 1mA

Low Battery Indication  “ 

 

” is displayed

Overrange Indication 

“OL” is displayed

Measurements Rate 

2 per second, nominal

Input Impedance 

7.8MΩ (VDC and VAC)

Display 

4000 counts LCD

AC Current 

50/60Hz (AAC)

AC Voltage Bandwidth   50/400Hz (VAC)
Operating Temperature  14 to 122°F (-10 to 50°C)
Storage Temperature 

-14 to 140°F (-30 to 60°C)

continued ...

Summary of Contents for ST-333













Reviews: