background image

7

2.

Apply the measuring liquid to the sample well (minimum of 0.3ml).

Note:

 For accurate measurements, it is recommended to completely cover 

the sample well surface.

The temperature of the measuring liquid should be the same as the  

ambient temperature. If the temperature is different, allow the liquid  

to adjust to the ambient temperature before taking a measurement.

3.

When ready, close the protective cover and press the 

START

 button

to take a measurement.

4.

A series of dashes ( – – – ) will appear on the display followed by the
measured Brix value (%) and the temperature value of the liquid sample.

5.

Remove the liquid sample by wiping it off with a tissue properly
clean the sample well as highlighted in the 

"Sample Well

Maintenance"

 section.

Auto Power Off

To preserve battery life, the meter is programmed to turn off after 
approximately 2 minutes of inactivity.

Sample Well Maintenance

Cleaning of the sample well should be performed immediately after each 
sample reading. Never immerse the meter in any liquid. When the sample 
well has been completely cleaned no residue should be present.
To properly clean the sample well use Isopropyl Alcohol followed by a 
distilled water rinse and then thoroughly dry with the included cleaning 
cloth, a residue free cloth or delicate task wipes.

Charging the Battery

1.

Connect the R9510 via the included cable to a USB port on your PC
or into a wall outlet using a USB Power Adapter (not included) to
charge the Li-ion battery.

Note:

 The meter must remain powered off to properly charge via the 

USB port on your PC.
2.

Charge the meter until the battery indicator appears full and remove
the charging cable when done.

 

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Summary of Contents for R9510











Reviews: