Kado Aspect Swivel Heated Towel Rail Wall Mount
635mm x 400mm Chrome
Installation Instructions
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Kado Aspect Swivel Heated Towel Rail Wall Mount
635mm x 400mm Chrome
Page 1 of 4
Installation instructions
WARNING:
This appliance is not intended for use by young children or infirm persons without supervision.
CAUTION:
The cord extension set must be positioned so that it is not subject to splashing or ingress of moisture.
The supply shall have means for disconnection with an air gap in all active conductors
incorporated in the fixed wiring according to the Wiring Rules in AS/NZS 3000:2000.
CAUTION
WARNING
This product must be installed by a qualified electrician in accordance with AS/NZS 3000 wiring rules. Switch off the electrical
supply at the mains before installation and maintenance. A means of disconnection must be incorporated in the fixed wiring
in accordance with the wiring rules. Suitable for bathroom and non-bathroom/dry areas. Not suitable for above baths, nor
for installation in saunas, steam rooms or shower cubicles. Please consult with a qualified electrician to confirm appropriate
compliant installation location.
Do not connect to a plug and socket outlet. Rated IPX5 and suitable for indoor use only. Do not fix to damp or conductive
surfaces. Site well away from curtains and fabrics. Switch off after use. Do not leave on for prolonged periods. This appliance is
not to be used by persons (including children) with reduced physical, sensory or mental capabilities.
Please consult with a qualified electrician to confirm appropriate compliant installation location.
HYDROTHERM
MILAN HEATED WALL MOUNT TOWEL RAILS
INSTALLATION
• Slide the WALL BRACKET
1
into the BRACKET ARM
2
and hold up to the wall in position.
• With a pencil, outline the WALL BRACKET
1
in the desired
position and remove from the wall.
• Using a pencil and the WALL BRACKET
1
, mark the centre
screw hole and cross it for accuracy.
• Drill a hole for the SCREW 4 and insert nylon plug into tiled
wall (if applicable). Installer may choose to use alternative
screws to suit the application.
• Position WALL BRACKET
1
so that the GRUB SCREW hole
faces directly down towards the floor and place SCREW
4
into the wall.
DO NOT OVERTIGHTEN SCREW - LEAVE SLIGHT
ADJUSTMENT OF THE FLANGE (SLACK) TO ENABLE
MOVEMENT WHEN THE TOWEL RAIL IS POSITIONED.
• When all of the WALL BRACKETS
1
are in place, slide
the TOWEL RAIL
5
into position towards the wall, until
BRACKET ARM
2
reaches the WALL BRACKET
1
.
• Insert GRUB SCREW
3
through BRACKET ARM
2
and into
WALL BRACKET
1
.
• With the ALLEN KEY
6
provided, tighten the GRUB SCREW
until tight to ensure that towel rail stays in position.
Please ensure that the measurements are taken accurately and
that the screw is in a stud or noggin to provide support. Do not
overtighten screws.
WARNING
All rails are individually hand made.
Due to this fact some measurments may not be exact.
PLEASE READ INSTRUCTIONS CAREFULLY
and do
not force towel rail into bracket if position of wall flange is not
accurate.
INSTALLING BRACKET
S
WARNING
Hydrotherm take pride in the fact that all rails are individually hand made. Due to this fact
some measurements may not be exact. PLEASE READ INSTRUCTIONS CAREFUL
LY and do not
force towel rail into bracket if position of wall
fl
ange is not accurate.
TOWEL RAILS MU
STALWAYS BE IN
STALLEDWITHTHE ELEMENT
PLACEDATTHE BOTTOM FOR CORRECT HE
ATTRANSFER
•
Slide the WALL BRACKET
1
into the BRACKET ARM
2
and hold up to the wall in position.
•
With a pencil, outline the WALL BRACKET
1
in the
desired position and remove from the wall.
•
Using a pencil and the WALL BRACKET
1
, mark the
centre screw hole and cross it for accuracy.
•
Drill a hole for the SCREW
4
and insert nylon plug into
tiled wall (if applicable). Installer may choose to use
alternative screws to suit the application.
•
Position WALL BRACKET
1
so that the GRUB SCREW
hole faces directly down towards the floor and place
SCREW
4
into the wall.
DO NOT OVERTIGHTEN SCREW - LEAVE SLIGHT
ADJUSTMENT OF THE FLANGE (SLACK) TO ENABLE
MOVEMENT WHEN THE TOWEL RAIL IS POSITIONED.
•
When all of the WALL BRACKETS
1
are in place, slide
the TOWEL RAIL
5
into position towards the wall, until
BRACKET ARM
2
reaches the WALL BRACKET
1
.
•
Insert GRUB SCREW
3
through BRACKET ARM
2
and
into WALL BRACKET
1
.
•
With the ALLEN KEY
6
provided, tighten the GRUB
SCREW until tight to ensure that towel rail stays in position.
2
3
2
1
1
3
6
6
4
4
5
5
**INSTALLER MAY CHOOSE NOT TO USE SCREW IF NOT SUITABLE FOR APPLICATION
Wall Bracket
Wall Screw**
Hydrotherm Towel Rail
Alen Key & Grub Screw
Bracket Arm
Grub Screw
Hydrotherm will not accept
responsibility for incorrectly
installed brackets.
Please read instructions carefully.
Please ensure that the measurements are taken accurately
and that the screw is in a stud or noggin to provide support.
Do not overtighten screws.
STUD OR
NOGGIN
WALL
INSTALLING BRACKET
S
T O W E L R A I LS
W
LY and do not
force towel rail into bracket if position of wall
fl
ange is not accurate.
TOWEL RAILS MU
STALWAYS BE IN
STALLEDWITHTHE ELEMENT
PLACEDATTHE BOTTOM FOR CORRECT HE
ATTRANSFER
•
Slide the WALL BRACKET
1
into the BRACKET ARM
2
and hold up to the wall in position.
•
With a pencil, outline the WALL BRACKET
1
in the
desired position and remove from the wall.
•
Using a pencil and the WALL BRACKET
1
, mark the
centre screw hole and cross it for accuracy.
•
Drill a hole for the SCREW
4
and insert nylon plug into
tiled wall (if applicable). Installer may choose to use
alternative screws to suit the application.
•
Position WALL BRACKET
1
so that the GRUB SCREW
hole faces directly down towards the floor and place
SCREW
4
into the wall.
DO NOT OVERTIGHTEN SCREW - LEAVE SLIGHT
ADJUSTMENT OF THE FLANGE (SLACK) TO ENABLE
MOVEMENT WHEN THE TOWEL RAIL IS POSITIONED.
•
When all of the WALL BRACKETS
1
are in place, slide
the TOWEL RAIL
5
into position towards the wall, until
BRACKET ARM
2
reaches the WALL BRACKET
1
.
•
Insert GRUB SCREW
3
through BRACKET ARM
2
and
into WALL BRACKET
1
.
•
With the ALLEN KEY
6
provided, tighten the GRUB
SCREW until tight to ensure that towel rail stays in position.
2
3
2
1
1
3
6
6
4
4
5
5
**INSTALLER MAY CHOOSE NOT TO USE SCREW IF NOT SUITABLE FOR APPLICATION
Wall Bracket
Wall Screw**
Hydrotherm Towel Rail
Alen Key & Grub Screw
Bracket Arm
Grub Screw
Hydrotherm will not accept
responsibility for incorrectly
installed brackets.
Please read instructions carefully.
Please ensure that the measurements are taken accurately
and that the screw is in a stud or noggin to provide support.
Do not overtighten screws.
STUD OR
NOGGIN
WALL
page 2 of 5
1
Twin Hole Wall Bracket (BOTTOM)
4
Wall Screw *
2
Single Hole Wall Bracket (TOP)
5
HydrothermTowel Rail
3
Grub Screw
6
Alen Key & Grub Screw
page 2 of 5
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
* Installer may choose not to use screw if not suitable for application.
TOWEL RAILS MUST ALWAYS BE INSTALLED WITH THE ELEMENT
PLACED AT THE BOTTOM FOR CORRECT HEAT TRANSFER
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive cleaners.
Damage caused by imporper treatment is not covered by the product warranty. Refer to Warranty Conditions.
KADO LUSSI WALL MOUNT HTR
