RedMax SGCX2600S Owner'S/Operator'S Manual Download | Manualshive

Page: 14 / 22

background image

■

ADJUSTING THE ANGLE OF THE CUTTING
BLADES (F2)

1. Stop the engine.
2. Turn the bolt located on the top of the trimming

mechanism counter-clockwise to loosen it.

3. Adjust the angle of the blades to the desired

angle, and then fix the bolt firmly back into place.

(1) Clamp lever
(2) Trimming mechanism

8. Operation

❲

14

❳

F2

«
...
12
13
14
15
16
...
»

Summary of Contents for SGCX2600S























Reviews:

No comments

Related manuals for SGCX2600S

Brand: Makita Pages: 10

Brand: Makita Pages: 2

Brand: Makita Pages: 3

Brand: Makita Pages: 2

Norton Clipper TR 201 E

Brand: SAINT-GOBAIN Pages: 20

Brand: ACMER Pages: 36

Brand: Niedax Pages: 10

Tough SQ84T SQUealer

Brand: Bush Hog Pages: 1

Brand: Bush Hog Pages: 1

TOUGH 2010 Series

Brand: Bush Hog Pages: 1

Brand: Bush Hog Pages: 150

Brand: Rayjet Pages: 53

STIGA PARK 125 COMBI PRO

Brand: Stiga Pages: 10

Brand: Olympia Tools Pages: 2

AUSTROFLIES 320

Brand: Kaufmann Pages: 2

Brand: IBEA Pages: 80

Brand: Tanaka Pages: 16

EXCALIBUR 1000X

Brand: KEENCUT Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands