RedMax CHTZ2500 Owner'S/Operator'S Manual Download Page 32

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the
emission control system warranty on your 1995 and later small off-road engine. In California,
new small off-road engines must be designed, built and equipped to meet the state’s stringent
anti-smog standards.   KOMATSU ZENOAH must warrant the emission control system on your
small off-road engine for the periods of time listed below provided there has been no abuse,
neglect or improper maintenance of your small off-road engine. 

Your emission control system may include parts such as the carburetor and the ignition system. 

Where a warrantable condition exists, KOMATSU ZENOAH will repair your small off-road engine
at no cost to you including diagnosis, parts and labor. 

Manufacturer’s warranty coverage: 

The 1995 and later small off-road engines are warranted for two years. If any emission-
related part on your engine is defective, the part will be repaired or replaced by
KOMATSU ZENOAH. 

Owner’s warranty responsibilities: 

– As the small off-road engine owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. KOMATSU ZENOAH
recommends that you retain all receipts covering maintenance on your small off-road
engine, but KOMATSU ZENOAH can not deny warranty solely for the lack of receipts or
for your failure to ensure the performance of all scheduled maintenance. 

– As the small off-road engine owner, you should be aware, however, that KOMATSU
ZENOAH may deny you warranty coverage if your small off-road engine or a part has
failed due to abuse, neglect, improper maintenance or unapproved modification. 

– You are responsible for presenting your small off-road engine to a KOMATSU ZENOAH
distribution center as soon as a problem exists. The warranty repairs should be
completed in e reasonable amount of time, not to exceed 30 days

If you have any questions regarding your warranty rights and responsibilities, you should
contact KOMATSU ZENOAH AMERICA INC. at (770)-381-5147 or you can write to 

KOMATSU ZENOAH AMERICA INC. 
4344 Shackleford Road Suite 500 
Norcross, Georgia 30093 

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT 

YOUR WARRANTY RIGHTS AND OBLIGATIONS 

Summary of Contents for CHTZ2500





































Reviews: