Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 137

Page: 137 / 178

B-11

Appendix B AN100U/UX Event Log Messages

Redline Communications Inc. Confidential and Proprietary

ODU upgrade process failed.

The ODU upgrade process failed.

This message is specific to the AN100UX. You
can retry the upgrade procedure or contact
[email protected].

Power Supply [X] is On

Where X is either A or B. This signifies
that the relevant power supply has
been detected and is properly
supplying power to the AN100U/UX.

Information only. There is no action required.

Primary RF Programming

This message indicates which one of
the three programming methods
succeeded when programming the
TB3436F7 radio (radio types 17 or 19
only).

• Secondary_0 RF Programming

• Secondary_1 RF Programming

Information only. There is no action required.

Radio Type [XX]: TBXXXXFX

This message confirms the type of
radio connected to the IDU. It should
match the radio type printed on the
ODU’s sticker.

Information only. There is no action required.

Secondary_0 RF
Programming

This message indicates which one of
the programming methods succeeded
when programming the TB3436F7
radio.

Information only. There is no action required.

Upgrade Failed. Default
Image Selected

The ODU upgrade process failed.

This message is specific to the AN100UX. You
can retry the upgrade procedure or contact
[email protected]

Upgrading the ODU...

The ODU upgrade is in progress. This
operation takes about 6 minutes.

Information only. There is no action required.

WARNING: Default Image is
Loaded

After the ODU upgrade, the new
firmware cannot be loaded into the
ODU FPGA. The default firmware is
loaded.

This message is displayed when the default
image cannot be loaded after an ODU upgrade
failure.

WARNING: ODU Temperature
is [c] Celsius

The operating temperature of the
AN100U/UX ODU is nearing the limit
of its operating temperature.

No action is taken until the
temperature exceeds the limit.

Most often caused by excessive ambient
temperatures.

Restore Messages

Restore configuration into
active image

The user-provided configuration file
has been applied to the active image

Information only. There is no action required.

Table B-1

AN100U/UX Event Log Messages (continued)

Message

Description

Comment

Summary of Contents for RedMAX AN100U



















































































































































































Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands

Redline Communications RedMAX AN100U, Administration And Maintenance Manual

Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands