background image

8

How to bind the receiver with the transmitter?

1) Insert the bind plug into Channel 4 before switching on the receiver.
2) Switch on the receiver. The LED light will flash.
4) Press and hold the SEL button on the transmitter.
The LED on the receiver will continue to flash. The radio is binding.
When the receiver's LED is lit solid, binding is complete.
Note: Repeat the above steps if binding fails.
5) Center the steering trim on the transmitter after binding is complete to set fail safe.
6) Remove the binding plug.

LED Indicator:

• RAPID FLASHING: BINDING IS IN OPERATION.
• SLOW FLASHING: NO SIGNA

L W

AITING FOR OPERATION

• SOLID LIGH

T

: IN OPERATION

• NO LIGH

T

: RECEIVER IS OFF, BA

TTERY

 IS DEAD OR MISSING,  RECEIVER IS 

  DISCONNECTED OR BROKEN

6. Turning the vehicle on/off

Transmitter Power Switch

To turn the vehicle on:

1. Switch on the transmitter.

2. Switch on the ESC power switch.
To turn off the vehicle:

1. Switch off the ESC power switch.

2. Switch off the transmitter.

Remember to remove the batteries from the vehicle and transmitter 

when not in use.

ESC power switch

Summary of Contents for RockSlide S10 XT





















Reviews: