background image

 

Inside US: +1 (877) 432-9908

Bulletin No. PAXLCL-E

Outside US: +1 (717) 767-6511

Drawing No. LP0567

www.redlion.net

Released  2018-01-26 

-1-

MODEL

  

PAXLCL

 ‐ 

PAX

 

LITE

 

CURRENT

 

LOOP

 

METER

 

DUAL RANGE, 4 to 20 mA or 10 to 50 mA *

 3 1/2-DIGIT, 0.56" (14.2 mm) HIGH RED LED READOUT

24 VDC EXCITATION SUPPLY

WIDE SPAN & OFFSET SCALING RANGE

OVER-RANGE INDICATION

SELECTABLE DECIMAL POINTS

NEMA 4X/IP65 SEALED FRONT BEZEL

 OPTIONAL CUSTOM UNITS OVERLAY W/BACKLIGHT

* Also adapts to 0 to 50, 0 to 20, 0 to 10, 1 to 5 mA ranges as well as

bi-polar inputs.

GENERAL

 

DESCRIPTION

The features of the PAX Lite Series can be applied to measurement of

process variables. With its high sensitivity and programmability, the PAX
Lite Current Loop Meter can be set up for a wide variety of applications.
The PAXLCL can be used for most current loop meter needs for readout
of pressure, flow, temperature, level and other variables. The meter has
been specifically designed for harsh industrial environments. With NEMA
4X/IP65 sealed bezel and extensive testing of noise effects to CE
requirements, the meter provides a tough yet reliable application solution.
This allows the PAXLCL to be used in dirty, hostile environments and in
wash-down areas. The 3 1/2-digit bi-polar display (minus sign displayed
when current or voltage is negative) features 0.56" (14.2 mm) high, 7-
segment LEDs for easy reading.

SAFETY

 

SUMMARY

All safety related regulations, local codes and instructions that appear

in the literature or on equipment must be observed to ensure personal
safety and to prevent damage to either the instrument or equipment
connected to it. If equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be impaired. 

CAUTION: Risk Of Danger.

Read complete instructions prior to 

installation and operation of the unit.

CAUTION: 

Risk of electric shock.

DIMENSIONS

 

In

 

inches

 

(mm)

Note: Recommended minimum clearance (behind the panel) for mounting clip installation is 

2.1" (53.4) H x 5.0" (127) W.

1 2 3 4 5 6

7

8 9 10

3.60 (91.4)

(44.5)

1.75

(96.5)

3.80

1.95

(49.5)

(2.5)

.10

(104.1)

4.10

(44.5)

1.75

mA

C

US LISTED

UL

R

PROC. CONT. EQ.

E179259

Summary of Contents for PAXLCL Series









Reviews: