Chapter 4. Getting In and Out of gdb
15
-async
Use the asynchronous event loop for the command-line interface. gdb processes all events, such
as user keyboard input, via a special event loop. This allows gdb to accept and process user
commands in parallel with the debugged process being run
1
, so you don’t need to wait for control
to return to gdb before you type the next command. (
Note:
as of version 5.1, the target side of
the asynchronous operation is not yet in place, so
-async
does not work fully yet.)
When the standard input is connected to a terminal device, gdb uses the asynchronous event loop
by default, unless disabled by the
-noasync
option.
-noasync
Disable the asynchronous event loop for the command-line interface.
-args
Change interpretation of command line so that arguments following the executable file are passed
as command line arguments to the inferior. This option stops option processing.
-baud
bps
-b
bps
Set the line speed (baud rate or bits per second) of any serial interface used by gdb for remote
debugging.
-tty
device
-t
device
Run using
device
for your program’s standard input and output.
-tui
Activate the Terminal User Interface when starting. The Terminal User Interface manages several
text windows on the terminal, showing source, assembly, registers and gdb command outputs
(refer to Chapter 24
gdb Text User Interface
). Do not use this option if you run gdb from Emacs
(refer to Chapter 25
Using gdb under gnu Emacs
).
-interpreter
interp
Use the interpreter
interp
for interface with the controlling program or device. This option is
meant to be set by programs which communicate with gdb using it as a back end (refer to Chapter
23
Command Interpreters
.
-interpreter=mi
(or
-interpreter=mi2
) causes gdb to use the current
gdb/mi interface
(refer to Chapter 26
The gdb/mi Interface
). The previous gdb/mi interface, included in gdb ver-
sion 5.3, can be selected with
-interpreter=mi1
. Earlier gdb/mi interfaces are not supported.
-write
Open the executable and core files for both reading and writing. This is equivalent to the
set
write on
command inside gdb (refer to Section 16.6
Patching programs
).
-statistics
This option causes gdb to print statistics about time and memory usage after it completes each
command and returns to the prompt.
1. gdb built with djgpp tools for MS-DOS/MS-Windows supports this mode of operation, but the event loop is
suspended when the debuggee runs.
Summary of Contents for ENTERPRISE LINUX 4 - DEVELOPER TOOLS GUIDE
