background image

Rear View Safety  

Reverse With Confidence

 ™

4

5

Please read the entire manual and follow the instructions and 

warnings carefully. Failure to do so can cause serious damage and/or 

injury, including loss of life. Be sure to obey all applicable local

 traffic and motor vehicle regulations as it pertains to this product. 

Improper installation will void manufacturer’s warranty.

The Rear View Camera System is

designed to help the driver safe-
ly detect people and/or objects 
helping to avoid damage or injury. 
However, you the driver, must use it 
properly. Use of this system is not a 
substitute for safe, proper or legal 
driving.

Never back up while looking at the

monitor alone. You should always 
check behind and around the vehi-
cle when backing up, in the same 
way as you would if the vehicle did 
not have the Rear View Camera 
System. If you back up while looking 
only at the monitor, you may cause 

damage or injury. Always back up 
slowly.

The Rear View Camera System is

not intended for use during exten-
sive back-up maneuvers or backing 
into cross traffic or pedestrian walk-
ways.

Please, always remember, the area

displayed by the Rear View Camera 
System is limited. It does not display 
the entire panorama that is behind 
you. 

USAGE:

Electric shock or product

malfunction may occur if this 
product is installed
incorrectly.

Use this product within

the voltage range specified. Failure 
to do so can cause 
electronic shock or product 
malfunction.

Take special care when

cleaning the monitor.

Make sure to firmly affix the prod-

uct before use.

If smoke or a burning smell

is detected, disconnect the 
system immediately. 

Where the power cable may touch

a metal case, cover the cable with 
friction tape. A short circuit 

or disconnected wire may cause a 
fire.

While installing the Rear View

System be careful with the wire 
positioning in order to avoid wire 
damage.

The Rear View System should only

be used when the vehicle is in 
reverse.

Do not watch movies or

operate the monitor while driving; 
as it may cause an
accident.

Do not install the monitor

where it may obstruct drivers
view or obstruct an air bag
device.

Dropping the unit may cause

possible mechanical failure.

INSTALLATION:

SAFET

Y   INF

ORMA

TION

SAFET

Y   INF

ORMA

TION

Summary of Contents for RVS-Pickup










Reviews: