background image

Rear View Safety  

Reverse With Confidence

 ™

8

9

Replacement Monitor

The mirror monitor replaces the existing car mirror. Carefully remove 
the mirror off the “pin”. Slide the replacement mirror on to the pin and 
secure it with the screw provided (already in the screw hole).Differ-
ent cars have different brackets. Depending on your vehicle make and 
manufacturer. There are many methods to remove the original rear-
view mirror, however, please don’t force the mirror off the bracket.
The manufacturer will not be responsible for damage caused to your 
car by wrong installation of the mirror. Figure 1.1

Clip-On Monitor

1. The Mirror Monitor attaches to the existing rear view mirror in
vehicle with the pressurized clips on the back of the monitor.
2. Attach monitor to existing mirror, and adjust mounting angle to
allow optimum driver viewing comfort. 

Camera & Cable

Be sure to position the cable properly. The aviation camera cable uses 
aircraft grade connectors which means the camera cable can be ex-
posed to all weather elements. Do not run the cable over sharp edges, 
do not kink the cable and keep away from HOT and rotating parts.
Fasten all cables and secure all excess cable. Connect camera to the 
camera extension cable which runs inside the vehicle. Figure 1.2

Wiring

After connecting the camera to the “camera cable” the camera should 
be plugged into AV2 input. Connect the RED 12V power wire to an igni-
tion power source and the BLACK 12V ground wire to a chassis ground. 
The GREEN wire is the REVERSE trigger wire. Connect this wire to the 
vehicle’s backup light circuit to activate the rear-view image whenever 
the vehicle shifts into reverse. To connect a second camera, connect it 
to AV1 input. It can be turned on by pressing the power button on the 
monitor. Figure 2.1, Figure 2.2

Precautions For Use Of Mirror Monitor

I.  

The Mirror Monitor is made of glass. Do not subject it to a 
mechanical shock by dropping it from a high place, etc.

II.

Do not apply excessive force to the monitor surface or the
adjoining areas since this may cause the color tone to vary.

III.

Clean with a soft dry cloth and/or Windex only.

IV.

Do not attempt to disassemble the mirror monitor.

Safety

• Before drilling, be sure no cable or wire is on the other side.
• Feed as much cable as possible into vehicle & clamp securely.

This reduces the possibility of cable being hooked or snagged.

INST

ALL

ATION  GUIDE

INST
ALL

ATION  GUIDE  +  TIPS 

Summary of Contents for RVS-776718-BB


















Reviews: