manualshive.com logo in svg

Realtek Ameba-D RTL872 D Series, User Manual

The Realtek Ameba-D RTL872 D Series features cutting-edge technology for high-performance IoT devices. Unlock the full potential of your device with the comprehensive User Manual, available for free download at our website. Find everything you need to get started and maximize your experience with this advanced product.

Share
Download
background image

                                                           

      Audio Codec Controller (ACC) 

User Manual                                                                                                                       All information provided in this document is subject to legal disclaimers.                                                            © REALTEK 2019. All rights reserved.

 

381 

18

 

Audio Codec Controller (ACC) 

18.1

 

Introduction 

Ameba-D audio codec control (ACC) is the bridge between host audio buffers and audio codec module.  
 
It transfers audio data to or from audio codec module via SPORT sequentially according to user settings, such as sample rate, sampling 
resolution, channel number, etc.  
 
On the other hand, Ameba-D drives the audio codec module to work well by means of ACC, which is implemented via SI bus. 

18.2

 

Features 

 

Mandatory or optional sample rate which audio codec module declares to support 

 

8-bit/16-bit/24-bit sampling resolution 

 

Mono/stereo audio 

 

I

2

S/left-justified/PCM data formats 

 

GDMA interface for data flow 

 

Data loopback between SDI and SDO 

18.3

 

Architecture 

The ACC is used for audio codec input/output control. The ACC and AC architecture of Ameba-D is shown in Fig 18-1. 
 

GDMA

Memory

APB

Bridge

SI Slave

Digital Core

I2S/PCM

Audio Codec @40MHz

Analog Core

I2S/PCM

SI

@40MHz

SPORT

@40MHz or 256*Fs

ACC

 

Fig 18-1 Ameba-D ACC + AC architecture 

18.3.1

 

Block Diagram 

The ACC block diagram is shown in Fig 18-2. 
 

Realtek confidential files

The document authorized to

SZ99iot

2019-05-15 10:08:03

Summary of Contents for Ameba-D RTL872 D Series















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ameba-D RTL872 D Series

P&E Microcomputer Systems xPC560B User Manual preview
xPC560B
Brand: P&E Microcomputer Systems Pages: 59
MSI MS-7032 Instruction Manual preview
MS-7032
Brand: MSI Pages: 92
Wiznet WizFi360-EVB-Pico Getting Started Manual preview
WizFi360-EVB-Pico
Brand: Wiznet Pages: 29
Silicon Laboratories Si5338-EVB User Manual preview
Si5338-EVB
Brand: Silicon Laboratories Pages: 16
CHAINTECH 9EJS1 User Manual preview
9EJS1
Brand: CHAINTECH Pages: 59
Energy EFM32 G890 Manual preview
EFM32 G890
Brand: Energy Pages: 14
XFX nForce 780i User Manual preview
nForce 780i
Brand: XFX Pages: 120
ECS A970M-A DELUXE Manual preview
A970M-A DELUXE
Brand: ECS Pages: 74
OLIMEX ESP8266 Series Upgrade Manual preview
ESP8266 Series
Brand: OLIMEX Pages: 17
Texas Instruments bq76925EVM User Manual preview
bq76925EVM
Brand: Texas Instruments Pages: 44
Congatec Qseven conga-QA5 User Manual preview
Qseven conga-QA5
Brand: Congatec Pages: 61
Gigabyte 5SG100 User Manual preview
5SG100
Brand: Gigabyte Pages: 19
Cebekit UCPIC-7 Manual preview
UCPIC-7
Brand: Cebekit Pages: 8
Rohm BD7F100EFJ-EVK-002 User Manual preview
BD7F100EFJ-EVK-002
Brand: Rohm Pages: 6
Acorp 4S661QP Manual preview
4S661QP
Brand: Acorp Pages: 74
Texas Instruments DRV2605 User Manual preview
DRV2605
Brand: Texas Instruments Pages: 34
Gigabyte GA-946GZ-DS3 User Manual preview
GA-946GZ-DS3
Brand: Gigabyte Pages: 80
Advantech AIMB-286 User Manual preview
AIMB-286
Brand: Advantech Pages: 136

Brands by name

Popular brands

Load more brands