background image

-10- 

 

10.

 

WEEE - WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT  

 

 

The symbol on the product or on its packing indicates that this product 
may not be treated as household waste. Instead it shall be handed over 
to the applicable collection point for the recycling of electrical and 
electronic equipment. By ensuring this product is disposed of correctly, 
you will help prevent potential negative consequences for the 
environment and human health, which could otherwise be caused by 
inappropriate waste handling of this product. For more detailed 

information about recycling of this product, please contact your local city office, your 
household waste disposal service or the shop where you purchased the product. 

11.

 

WARRANTY  

 

 

This product is warranted for a 12 months period effective from the date of 
purchase by the first user. 

 

Damage and/or defects resulting from inappropriate use do not fall under the 
warranty provisions. 

 

We also disclaim all liability for any bodily injury resulting from inappropriate use 
of the tool. 

 

At the same time, no claim can be made on the warranty if the damage of the 
device is the result of negligent maintenance or overload. 

 

Definitely excluded from the warranty is damage resulting from fluid permeation, 
excessive dust penetration, intentional damage (on purpose or by gross 
carelessness), inappropriate usage (use for purposes for which the device is not 
suitable), incompetent usage (e.g. not following the instructions given in the 
manual), inexpert assembly, lightning strike, erroneous net voltage. This list is not 
exhaustive. 

 

Acceptance of claims under warranty can never lead to the prolongation of the 
warranty period nor commencement of a new warranty period in case of a device 
replacement. 

 

We reserve the right to reject a claim whenever the purchase cannot be verified or 
when it is clear that the product has not been properly maintained (Clean 
ventilation slots, carbon brushes serviced regularly, etc.). 

 

Any transportation costs shall always be borne by the customer, unless agreed 
otherwise in writing. 

 

You can always obtain more information by the email 

[email protected] 

or at 

the number 

888-899-1688

Summary of Contents for BY01-HBE













Reviews: