REA JET HR pro 2K User Manual Download Page 124

Page: 124 / 189

Instruction manual

Page 124 / 189

REA JET HR

pro

2K / 4K

V 3.5x_001 28.05.2015

4.2.17.1.1

Cold device connection cable

A cold device connection cable is part of the delivery

4.2.18

Installation of the print heads

The connections of the control device, A9, A10, A15 and A16, can each accommodate one print
head per connection.

Figure 166: View of the control device on the print head

(arrow)

Figure 167: Scope of delivery print head cable



Print head cables can only be connected or disconnected

the control device has been deactivated



Any damages arising from non-observance of these
requirements are not covered by the guarantee.



The print head cables are symmetric (= no predefined usage).

Summary of Contents for JET HR pro 2K






























































































































































































Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands

REA JET HR pro 2K, User Manual

Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands