REMOTE CONTROL FOR ZONE 1 MIXER INPUTS 2, 3 AND 4
ZONE 2
EFFECTS LOOP
AUTOMATIC SLEEP MODE
ADDING ZONES
OPERATION
External 0 to 10 V Control
Pin 1
0 to 10 V for Input 2
Pin 3
0 to 10 V for Input 3
Pin 5
0 to 10 V for Input 4
Pin 8
Ground Reference
Input 4 External 10k Ω Pot.
Input 3 External 10k Ω Pot.
Input 2 External 10k Ω Pot.
Upon loss of audio at all inputs, a timer starts. At the completion of the timing interval, the mixer amplifier enters the standby mode. All circuits not needed to detect audio presence are shut
off. When audio is detected, all circuits turn on and wait for a loss of audio to restart the timing interval. The timer may be disabled if required by system specifications.
The Zone 2 mixer operates from the same 4 inputs as the front-panel Zone 1 mixer. Ducking assignments do not affect the signals in Zone 2. Each input source should be adjusted to the
desired output level. Turn down unused inputs to remove them from the mix. Three Zone 2 outputs are provided. The LINE OUTPUT is balanced and may be used to feed the input of an other
power amplifier. The 600 Ohm output is transformer isolated (providing galvanic isolation) to drive a phone PBX paging input. The 8 Ohm output drives an 8 Ohm speaker with up to 4 W RMS.
REMOTE MIXING CONTROL
Connect this RJ45 jack directly to an RDL
remote control. (Examples: D/DS-RC3 or
D/DS-RC3M) The RJ45 wiring may be
“broken out” for connection to external
OEM 0 to 10 Vdc controls or 10k Ohm
potentiometers.
WIRING “Break-out”
LINE OUTPUT
Active balanced
INPUTS
Adjust for desired
output level
10 Minutes
40 Minutes
70 Minutes
100 Minutes
20 Minutes
50 Minutes
80 Minutes
110 Minutes
Disable (mixer-amplifier remains
ON, does not enter standy mode)
30 Minutes
60 Minutes
90 Minutes
120 Minutes
PIN 1, Mixer Input 2 VCA control
PIN 2
PIN 3, Mixer Input 3 VCA control
PIN 4
PIN 5, Mixer Input 4 VCA control
PIN 6
PIN 7, +10 Vdc
PIN 8, Ground Ref.
RJ45 Control Wiring
PIN 5, VCA control
PIN 7, +10 Vdc
PIN 8, Ground Ref.
CCW
CW
PIN 3, VCA control
PIN 7, +10 Vdc
PIN 8, Ground Ref.
CCW
CW
PIN 1, VCA control
PIN 7, +10 Vdc
PIN 8, Ground Ref.
CCW
CW
EFFECTS LOOP CONNECT SWITCH
This switch is normally left in the ON (up)
position when the effects loop is not used.
The switch connects the preamp output from
the Zone 1 mixer directly to the input of the
Zone power amp stage. Set this switch OFF
(down) to insert external processing.
MODULE MOUNTING AREA
This area is reserved for mounting RDL STICK-ON
or TX-Series modules. This example shows a
high-pass filter to protect horn loudspeakers from
bass overload. Other effects possibilities include
equalizers, mixers, crossovers or processors.
MODULE POWER
24 Vdc, 100 mA is available to power external modules.
Balanced LINE signal feeds phone PBX
Note: Remote control labels for
INPUTs 1, 2 and 3 correspond to
mixer-amplifier inputs 2, 3 and 4
respectively.
Connect an 8 Ohm speaker or multiple
speakers configured to present an 8 Ohm
load to the amplifier.
EQUALIZATION
Set the switch to
EQUALIZED (in) if the
front-panel tone controls
should affect the line
output; Set to FLAT (out)
if the tone controls should
not affect the line output.
SIGNAL PRESENT
The green LED glows when audio is present at INPUT 1. The indication is not affected by the setting of the mixer level control.
MIXER LEVEL 1
Adjust the level control for the desired output level. INPUT 1 is usually the paging signal. The level for this source is
set on the front panel and is unaffected by the remote control. Inputs 2, 3 and 4 are adjusted using the level controls
on the remote control. Note: Multiple compatible RDL remote controls are available separately.
POWER INDICATOR
Glows dimly when unit is powered in
standby (sleep) mode; glows bright when
amplifier is on; flashes during power-up.
POWER BUTTON
Momentary pushbutton toggles the
amplifier between ON and STANDBY.
TONE CONTROLS
Adjust BASS and TREBLE as desired.
COMPRESSION INDICATOR
LED flashes when audio compressor is
acting on the amplified audio.
ADDITIONAL ZONE AMPLIFIERS
Connect the LINE OUTPUT to the line input of one or
multiple additional RDL amplifiers to permit the Zone 1
mixer to feed other zones. The LINE OUTPUT may be
set to provide “flat” audio or to allow equalization by the
front-panel tone controls. The LINE OUTPUT may also be
used to feed recording equipment or an audio distribution
amplifier.
RDL
•
659 6th Street
•
Prescott, AZ
•
USA 86301
•
Sales: 800-281-2683
•
928-443-9391
•
Tech Support: 800-933-1780
•
928-778-3554
•
RDL Europe Sales & Support: (31) 20-6238-983
•
www.rdlnet.com
Copyright © 2011 Radio Design Labs, Inc. RDL, Radio Design Labs and the RDL logo are registered trademarks of Radio Design Labs, Inc. Data reflects product at publication time, subject to change without notice. “Made in USA” applies to all HD products except power supplies. Other trademarks, if any, are the property of their respective owners.
891-3355A
ZONE 1 OUTPUT CONNECTIONS
Unplug the power supply and remove the output terminal security cover. Connect constant voltage speakers to a single output voltage tap. Do not connect speakers with dissimilar voltages to multiple
output taps. Total connected load must not exceed 35 W. Upon completion of the output terminal block wiring, re-install the cover over the terminal block prior to plugging in the power supply.
Multiple 25 V speakers
Multiple 70 V speakers
Multiple 100 V speakers
