RCGF 21CC-Twin Operator'S Manual Download Page 4

which can foul the engine and exhaust ports, resulting in reduced performance. Synthetic 

oils also reduce friction and provide more fluidity at low temperatures. 

●  Do  not  install  your  throttle  servo  or  kill  switch  servo  inside  the

  engine compartment. 

Doing so could cause radio interference.  Install all electronic radio devices as far away 

from the engine as possible. 

● The throttle and choke pushrods should be non

-metallic. 

● If the engine is not to be used for more than a month, drain the

 fuel tank and remove 

any fuel from inside the carburetor. Do this by running the engine at idle until it quits by 

running out of fuel.Keeping gasoline inside the carburetor over an extended period of 

time will damage the diaphragm valve and clog passages inside  the  carburetor. Due to 

the carburetor being more complicated  than those used in glow engines, keep the fuel 

clean by using a fuel filter. Use a filter intended to be used with gasoline engines. Metal 

filters intended for glow engine are too coarse and will not screen out finer particles. 

● Always filter your fuel by using an appropriate filter before putting

 it into the airplane’s 

fuel tank. 

● Gasoline is extremely flammable. Keep it away from an open

 flame, excessive heat or 

sources of sparks. 

● Do not smoke n

ear the engine or the fuel tank. 

● This engine was designed for use in a model aircraft. Do not

 attempt to use it for any 

other purpose. 

● Always install an ignition system kill switch on the aircraft used.

 

  Do not install your throttle servo or kill switch servo inside the engine compartment. 

Doing so could cause radio interference.Install all electronic radio devices at least 12” 

[305mm] away from the engine. 

● Caution: Running the engine with a lean gas mixture will cause

 the engine to overheat 

and burn  the electrode of the spark plug.  Pay close attention to the High-speed Needle 

adjustment. Running the engine with the proper gas mixture will cause the spark plugs 

to appear yellow at the ignition point. 

● For optimum performance please use fresh or recen

tly purchased 93 octane gasoline 

(87 octane gasoline will suffice) with a 30:1 gas/oil mixture. 

 

GAS/OIL Mixing Chart 

1 Gallon Gasoline (128 fl oz/3.78L) / 2-Cycle Oil 

(4.26fl oz/125.68ml) = 30:1 ratio 

●  Excessive  running  of  the  engine  at  idle  speed  can  re

sult in a  seriously carbonized 

spark plug. 

● Keep the surface of the engine clean to ensure proper heat

 dissipation. Ensure proper 

cooling/ventilation around the cylinder with adequate air exhaust. 

● To

 avoid permanent damage to the electronic ignition system, never rotate the propeller 

on your RCGF engine with the electronic  ignition system switched on and the plug not 

installed in the plug cap. 

 

Summary of Contents for 21CC-Twin






















Reviews: