Model
Voltage
(Nominal)
Vdc
Capacity
(Nominal)
Ah
Charge
Temperature Range
Operating
Temperature Range
Hovertrax 2.0
36
2.5
0˚ to 40˚C
32˚ to 104˚F
-10˚ to 40˚C
14˚ to 104˚F
5
Need Help?
Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at
www.razor.com
. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
CHARGING THE BATTERY
Your Hovertrax 2.0 comes with a built-in Li (NiCoMn)O2 battery pack. Your Hovertrax 2.0 may not have a fully charged
battery; therefore you must charge the battery prior to use. Be sure to charge the battery in a clean, dry location away
from direct sunlight, flames or sparks.
2
Plug the charger into the charger
port on the Hovertrax 2.0. The
light on the charger should turn
red during charging. The light will
turn green again when charging is
complete.
1
Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note:
If green light (LED) does not
turn on, try a different outlet.
WARNING:
Use ONLY with the recommended
charger. Batteries are only to be
charged under adult supervision.
The charger is not a toy. Always
disconnect the charger before
wiping down and/or cleaning the
Hovertrax 2.0 with a damp cloth.
The charger supplied with the
Hovertrax 2.0 should be regularly
examined for damage to the cord,
plug, enclosure and other parts.
In the event of such damage, the
Hovertrax 2.0 must not be charged
until it has been repaired or
replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Wall outlet - Green (stand by)
Wall outlet and product - Red
(charging)
Wall outlet and product - Green
(charged)
Note:
Continue charging product
even if light turns green prior to 4
hours.
WARNING:
Failure to
recharge the battery at least once a
month may result in a battery that
will no longer accept a charge.
Charger
(Note: Charger design may vary
from one shown)
Note:
Make sure the power switch
is in the
OFF
position.
LED
• Use only Razor Hovertrax 2.0 charger.
• Initial charge time: 6 hours.
• Recharge time: up to 4 hours, even if the light turns green.
Recommended maximum charging time is 24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended periods
of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the Hovertrax 2.0 power switch is turned
OFF
when product is not in use. If the power switch is left on
for an extended period of time, the battery may reach a
stage at which it will no longer hold a charge.
• Run time: Up to 60 minutes of continuous ride time.
Run time may vary depending on riding conditions, rider
weight, climate, and/or proper maintenance.
• Constant stopping and starting may shorten ride time.
• Do not charge at or below 32º F (0º C).
• Do not allow charger or battery pack to overheat. If they seem warm, allow to cool down. Charge only at
room temperature.
• Do not place product or charger in the sun or warm environment. Keep at normal room temperature.
Battery Power Level Indicator
• When battery is in need of a charge the orange battery indicator light will turn off and the red (bottom) battery
indicator flash and the product will beep.
• Step off and charge. Do not attempt to ride until product has been recharged.
WARNING:
The
Hovertrax 2.0 will notify you when
the battery charge is dangerously
low by beeping. The orange
battery indicator light will turn
off and the red (bottom) indicator
light will begin to flash. If these
warnings occur, immediately slow
down and safely step off. Turn
the product off. Do not attempt
to ride again until the battery is
recharged.
Green
Orange
Battery Indicators
Red
Summary of Contents for HOVERTRAX 2.0
Page 2: ......