Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 103

Page: 103 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

10000001052

2.3.6.3

RoT & Radius

RoT

Use the + and - softkeys to adjust the max. turn rate for a heading/course

change. Press the SET button to transmit this value to the controller.

Value range: 5



/min to 500



/min (in increments of 1



/min).

Radius

Use the + and - softkeys to adjust the min. radius for a heading/course change.

Press the SET button to transmit this value to the controller.

Value range: 0.1 NM to 5.0 NM (in increments of 0.1 NM).

(NM = Nautical mile)

Selected

Use this pull-down menu to select a heading/course change mode.

This function is identical to the Rad/RoT softkey; see the first display of Figure 22.

Note:

Rad/Rot is not adjustable in mode Track Control with RAYTHEON

Anschütz ECDIS

Figure 52: RoT & Radius (Page function)

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands