Raytheon Anschütz ECDIS NX Compact System Manual Download Page 33 | Manualshive

Page: 33 / 53

background image

ECDIS NX Compact

2 Installation

Edition:001

23

10000000559

Fig. 17: Connection Overview, Allocation of Pins

Tab. 6: Allocation of Pins

Connector

Description

Pin

01

TxD- Transmit Data Negative

Pin

02

TxD+ Transmit Data Positive

Pin

03

GND Ground

Pin

04

RxD- Receive Data Negative

Pin

05

RxD+ Receive Data Positive

Pin

06

TxD- Transmit Data Negative

Pin

07

TxD+ Transmit Data Positive

Pin

08

GND Ground

«
...
31
32
33
34
35
...
»

Summary of Contents for ECDIS NX Compact






















































Reviews:

No comments

Related manuals for ECDIS NX Compact

Brand: Landoll Pages: 6

Brand: ParaBody Pages: 9

Brand: ParaBody Pages: 3

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: Panasonic Pages: 180

Brand: lancer Pages: 12

Brand: Keithley Pages: 42

Brand: B-K lighting Pages: 3

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: Madrigal Pages: 5

Brand: MacDon Pages: 504

Brand: Parkside Pages: 2

Brand: Park House Healthcare Pages: 12

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands