Raytheon Anschütz ECDIS NX Compact System Manual Download Page 27 | Manualshive

Page: 27 / 53

background image

ECDIS NX Compact

2 Installation

Edition:001

17

10000000559

Fig. 8: Connector, Plug into Housing

4. Finalize the installation by fasten the screws located in front on each side of the housing

connector.

Fig. 9: Connector, Tighten Connector

2.1.2

Installation Procedures

2.1.2.1

Install the Unit into a Console

About this task

WARNING!

Danger due to voltage-regulated devices

Risk of death or serious injury that is caused by electrical shock
• Switch off voltage supply if the wires have damaged insulation.

• Only skilled electricians must perform work on the electric system.

• Keep moisture away from live parts.

• Keep the system closed.

• Do not attempt to bypass or disable fuses.

You need: Torx T25 tool, 1 pcs of HD CMB SX1-B1 kit (included in delivery).

«
...
25
26
27
28
29
...
»

Summary of Contents for ECDIS NX Compact






















































Reviews:

No comments

Related manuals for ECDIS NX Compact

Brand: FagronLab Pages: 16

Brand: YSI Pages: 70

Brand: jcb Pages: 41

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: Dairyland Pages: 21

Brand: e+p Elektrik Handels Pages: 2

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: Olsen Pages: 58

Brand: Uchida Yoko Pages: 40

Brand: Uniden Pages: 32

Brand: Uniden Pages: 40

SUNDOWNER UH-011

Brand: Uniden Pages: 10

Brand: Zimmer Pages: 2

Brand: ZipRip Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands