background image

Raytec Americas: 

+1 613 270 9990 • [email protected]

Raytec Ltd reserve the right to change specifications without prior notification or public announcement.

Version 1

www.raytecled.com

1277-D

-0002

AR Bay luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, 
vibration and rough usage. This luminaire is certied by NSF for use in Splash-zone and Non-Food areas of food 
processing locations as defined in NSF-2. The AR Bay luminaire has been certified for use on marine vessels inside, 
outside, and in other severely wet saltwater environments.

UL 1598, UL 1598A, and UL 8750;
CSA 22.2 No. 250.0 and CSA22.2 No. 250.13
ABS Listed

2 x 3/4” NPT Conduit | Black: Line | White: Neutral | Green: Ground
Optional: Purple: 0-10V Dimming (+) | Grey: 0-10V Dimming (-)
For connections use wire rated to a minimum of 90°C. Class 1 Wiring only.
Dimming control wires must be rated 300V minimum for luminaires with suffix AC,
600V minimum for luminaires with suffix HV.

Certified to:

Connections:

Housing:

Ingress 
Protection:

Temperature 
Range:

Input Voltage:

Electrical Ratings:

Copper-free Cast Aluminium with Polycarbonate lens

IP66/67 | Suitable For Wet Locations. Marine Outside Type (Salt Water)

Based on luminaire suffix in table below: Suffix - AC: 120-277 VAC | Suffix - HV: 347-480 VAC

AR10, 15, 20, 25 AC Models: -40°C to +55°C
AR10, 15, 20, 25 HV Models: -40°C to +50°C
AR30 AC, HV Optical models: -40°C to +45°C
AR30 AC Flood model: -40°C to +40°C
AR30 HV Flood model: -40°C to +45°C

Application

Model

Input Voltage

Rated Wattage 

[Watts]

Rated Voltage 

[Volts]

Freqeuncy [Hz]

AR10

AC

107

120-277

50/60

HV

129

347-480

50/60

AR15

AC

145

120-277

50/60

HV

145

347-480

50/60

AR20

AC

190

120-277

50/60

HV

187

347-480

50/60

AR25

AC

247

120-277

50/60

HV

245

347-480

50/60

AR30

AC

312

120-277

50/60

HV

310

347-480

50/60

Surface/Ceiling Mounting Installation

E477827

SPI-AR

Summary of Contents for AR10
















Reviews: