P/N
241417
Rev 4
Effective: 12-04-12
Replaces: 10-07-11
Page 12
Resets board to factory default
settings.
Resets faults in the History File.
Change from Fahrenheit to Celsius.
SPA setpoint maximum adjustment.
POOL setpoint maximum adjustment.
Set Factory Defaults
Refer to step one above to access the program screen.
Set
Factory Defaults
should appear on the screen. If it does not,
press the
Mode
button until
Set Factory Defaults
appears
on the digital display. Press and hold both UP and DOWN
buttons for 5-7 seconds until
Defaults Set
appears. This op-
eration resets the operating program to its factory default val-
ues. Both the POOL and SPA setpoints will revert to 65°F
(18.5°C) and both POOL and SPA maximum temperature
settings will be 104°F (40.0°C). The Control Lockout PIN will
be cleared and the control will resume normal operation.
Clear Faults
Refer to step one above to access the program screen.
Press the
Mode
button until
Clear Faults
appears on the
digital display. Press and hold both UP and DOWN buttons
for 5-7 seconds until
Faults Cleared
appears. This operation
resets the Fault History file to “0” and clears all the stored
faults.
Program Button
1) Remove the four screws holding the control cover, and
swing the panel down so the back side of the board is
visible (see page 2). Locate the Program Mode button
(marked as SW1) as shown on page 15. Press and hold
the button (5-7 seconds) until
Set Factory Defaults
ap-
pears on the display. Release the program button.
2) Press the
Mode
button sequentially until the desired pro-
gram event is reached. There are 5 different events that
can be programmed. They appear in the sequence listed
below:
Fahrenheit or Celsius
Refer to step one above to access the program screen.
Press the
Mode
button until
Fahrenheit
or
Celsius
appears
on the digital display. The digital display is capable of dis-
playing Celsius as well as Fahrenheit temperatures. The UP
or DOWN buttons will select
Fahrenheit
or
Celsius
on the
temperature display. Choose the desired temperature scale.
Spa Max Temp – Spa Set Point Maximum Adjustment
Refer to step one above to access the program screen.
Press the
Mode
button until
Spa Max Temp
appears on the
digital display. Using the UP and DOWN buttons will change
the Maximum Temperature Setting to your desired value.
The control can be set for a maximum of 107°F.
Pool Max Temp – Pool Set Point Maximum Adjustment
Refer to step one above access into the program screen.
Press the
Mode
button until
Pool Max Temp
appears on the
digital display. Using the UP and DOWN buttons will change
the Maximum Temperature Setting to your desired value.
The control can be set for a maximum of 107°F.
Control Lockout
The heater is equipped with a Control Lockout feature to pre-
vent unauthorized tampering or adjustment of the control set-
tings. To lock out the controls, press the DOWN button and
Mode
button for 5 seconds. Choose a three digit PIN, using
the UP and DOWN buttons to select the digits and the
Mode
button to lock in selections. Confirm your selection and
record your PIN.
To unlock the controls, press any button to bring up the
Enter
PIN
menu. Enter the PIN that was used to lock the control.
Note that power cycling will
not
clear the lockout. Success-
fully unlocking the control will display “Lockout Cleared.”
Failure to enter the correct PIN will display “Invalid PIN.”
In the event that the user-selected PIN is lost or does not
clear the Control Lockout, use the Program Button to
Set
Factory Defaults
. This will clear the PIN and allow normal
operation and selection of a new PIN if desired. See the
Program Button
directions on this page for details.
NOTE:
Both the POOL and SPA setpoints will revert back
to 65°F (18.5°C) and the POOL and SPA maximum tem-
perature settings will be 104°F (40.0°C). These setpoints
will need to be readjusted to desired settings.
