manualshive.com logo in svg

Raymar 3460, User Manual, Page: 70 / 171

Share
Download
Raymar 3460 User Manual Download Page 70

3460 Fast’R

4-2

Getting Started With Fast’RVu

Fast’RVu is provided on the 3460 Fast’R CD-ROM. Refer to the 
readme.txt file on the CD-ROM.

When you run Fast’RVu, its main window opens (Figure 4-1).

Figure 4-1. Fast’RVu Main Window

Closing Multiple Fast’RVu Windows

IMPORTANT

: 

As you work in Fast’RVu, you may open multiple 

Fast’RVu windows. To exit Fast’RVu, always close the current window 
(by clicking the RETURN button or the Close icon (

), then any other 

Fast’RVu windows. If you close the Fast’RVU main window first (from 
the Windows Taskbar), you may find that, after Fast’RVu terminates, 
one or more subordinate Fast’RVu windows remain displayed. To close 
such a window, select 

File...Exit

, or click the Close icon (

).

Language 

Computer port 

Modem 

selection drop-

selection drop-

selection drop-

down menu

down menu

down menu

Tool bar

Summary of Contents for 3460












































































































































































Reviews:

No comments