background image

.

 

                                                                                             

 

User’s guide   Ytterbium Pulsed Fiber Laser   RFL-P20QB

P30QB   Ver.: 2.0 

 

 

 

5.

 

Instructions for warranty, return and maintenance 

5.1  General warranty 

All  products are warranted by Raycus against defects and problems in materials and 

workmanship during the warranty period according  to the purchase order or specifications and 

we guarantee the product will accord with the specification under normal use. 

Raycus  has the right to choose to repair or replace any product that proves to be defective in 

materials and workmanship selectively during the warranty period. Only products with particular 

defects are  under warranty. Raycus reserves the right to issue a credit  note for any defective 

products produced in normal conditions. 

5.2  Limitations of warranty 

The warranty does not cover the maintenance or reimbursement  of  our product  of which the 

problem  results  from  tampering, disassembling, misuse, accident, modification, unsuitable 

physical or operating environment, improper maintenance, damages due to excessive use or not 

following the instructions caused by those who are not from Raycus.  Customer has the 

responsibility to understand and follow this instruction to use the device. Any damage caused by 

fault operating is not warranted. Accessories and fiber connectors are excluded in this warranty. 

According to the warranty, client should write to us within 31 days since the defect is discovered. 

This warranty does not involve any other party, including specified buyer, end-user or customer 

and any parts, equipment or other products produced by other companies. 

5.3  Service and repairs 

Raycus is responsible for all the maintenance, for there is no accessory available inside for users 

to use. Please contact Raycus as soon as possible when problems under warranty  about 

maintenance happen to the product. The product returned with permission should be placed in a 

suitable container. If any damage happens to the product, please notify the carrier in document 

immediately. 

All the items about warranty and service above provided by Raycus are  only 

for reference; formal contents about warranty and service are subject to the 

contract.

 

Summary of Contents for RFL-P20QB














Reviews: