Raycus RFL-C1500X User Manual Download Page 35 | Manualshive

Page: 35 / 40

background image

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL- RFL-C1500X/C2000X

5 Alarms and Solutions

5.1 Alarms Display

When the laser establishes communication with the client software, all alarm states of the

laser can be displayed on Raycus software homepage, as shown in Figure 32(Download the

Rsycus software and software manual, please log in to Raycus official website)

Figure 15

The

homepage of Raycus software

If any alarm occurs (except for Interlock alarm) when the laser is running, the homepage

will display the alarm that occurs, and the ALARM light (yellow) on the front panel of the laser

will light up, the laser will stop emitting and lock.

When the Interlock is abnormal, the output of Ready signal is low, and the Interlock state is

abnormal in the software homepage, but the laser is not locked, and the ALARM light (yellow)

is not lit. The output of Ready signal is on high level when the Interlock is normal.

5.2 Alarm solutions

The instructions and solutions of alarms are as follows:

Table 11 Instructions and solutions for alarms of laser

«
...
33
34
35
36
37
...
»

Summary of Contents for RFL-C1500X









































Reviews:

No comments

Related manuals for RFL-C1500X

Brand: A&D Pages: 39

Brand: Lasertec Pages: 21

Brand: Keithley Pages: 18

SENSITRON SMART S

Brand: Halma Pages: 12

Brand: Quarton Pages: 2

Brand: Horiba Scientific Pages: 2

Brand: SensorLink Pages: 12

IEM-100 Beltpack

Brand: DAPAudio Pages: 17

Brand: PASI Pages: 59

Brand: Lutron Electronics Pages: 10

Brand: red lion Pages: 4

Brand: Lutron Electronics Pages: 23

Brand: Hanna Instruments Pages: 2

Brand: Vogel Pages: 4

K-PATENTS PR-23 AX Series

Brand: Vaisala Pages: 246

Brand: Feasa Pages: 145

Brand: Sonel Pages: 56

Brand: J-TECH Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands