manualshive.com logo in svg

raycop VCEN-100, Operating Manual

Share
Download
raycop VCEN-100 Operating Manual Download Page 15

15

Ho

w t

o U
se

PANTONE 7460C

Replacement of Consumables

Please make sure it is unplugged 

and the power is turned off before 

cleaning or replacing.

Warning

Release Lever

2

5

■Replacing the UV Lamp

※ If there is any defect within the first year, 

     the UV Lamp is covered by RAYCOP’s one-year warranty. 

     For more details contact customer support.

1

As shown on P.13, take out the grille. 

By using a drive, remove the 5 screws

in order to take out the UV Lamp 

Protective Tube.

Turn the UV Lamp release lever to 

unlock.

Turn on the device and verify if the 

UV Lamp is working properly by

checking the UV Lamp Indicator 

Light.

3

Take out the UV Lamp set from the 

release lever side.

4

In the reverse order of removing, 

attach the release leaver in the new

UV Lamp set and fit the rubber into 

the form. After hearing a click sound

and seeing the green point, turn it 

into 90 degrees and attach it to the 

device.

Caution

Take out the UV Lamp set from the 

release lever side.

Release Lever

Protective Tube

UV Lamp

UV Lamp

Indicator Light

Summary of Contents for VCEN-100





















Reviews:

No comments

Brands by name

Popular brands

Load more brands