Raychem HTC-915 Manual Download Page 2

CAUTION: installation, configuration and commissioning

should only be performed by properly trained personnel.

Local regulations regarding the installation & safety must be followed.

APPLICATION

Type 

Surface sensing/ambient sensing

Area of use 

Non-hazardous area indoors, typically panel mounted

Approval certification 

CE marked
 

 

PRODUCT SPECIFICATION

Temperature range controller 

–60°C to 570°C in steps of 1 K 

Control algorithms

EMR: Line sensing on/off, proportional ambient
SSR: Line sensing on/off, proportional, proportional ambient, power limiting, 

soft start

Switching accuracy 

1 K

ENCLOSURE

Ambient operating temperature range

–40°C to +50°C

Ambient storage temperature range

–40°C to +85°C

Relative humidity

0% to 90% Non condensing

Ingress protection

Housing: IP40, Terminals: IP20

Material

ASA-PC, color: green

Flammability class

V0 (UL94)

Mounting method

Panel mounting on 35 mm DIN rail

WARNING

   IEC 60417-5032 (2002-10) Alternating current

  IEC 60417-5031 (2002-10) Direct current

ELECTRICAL PROPERTIES

Connection terminals and cabling

Screw type terminals. All terminals suitable for stranded and solid core connection 

cables having a cross section between 0.5 and 2.5 mm2 (24 to 12 AWG) The 

915-HTC and 915-Alarm Relay connector outputs (240V) require ferrules on the 

connecting wires if stranded wires are used. The wires shall handle a minimum wire 

temperature of 75°C

Supply voltage 

CE/EAC: 100 Vac to 250 Vac, +10% -10%, 50/60 Hz, 0.15 A to 0.06 A 

CSA: 100 Vac to 277 Vac, 50/60 Hz, 0.15

Power consumption 

Max 20 VA with limiter connected

Control output 

Contactor control 

output

(EMR) Electromechanical relay rated 3 A/250 Vac, 50/60 Hz

Solid-state relay 

control output

(SSR) 12 VDC, 75 mA. max. to drive normally open Solid state relays. Depending on 

the application, one, two or three phase switching elements have to be used. (Solid 

state relays are not included)

Switching capacity

Depends on the type of switch element used 

(The switch element is external)

nVent.com  |  2

(Russia, Kazakhstan, Belarus)  

For other countries contact your local nVent representative.

TC RU C-BE.БЛ08.B.01634

Summary of Contents for HTC-915









Reviews: