background image

9

Upper Oven

The Rayburn Ranger® 

UPPER

 oven is indirectly heated by 

two elements, one concealed in the base of the oven and the 

other is visible in the roof (

Fig. 6.2

). These elements heat the 

twin walled cavity to provide cooking results consistent with 

traditional heat storage ovens, but with the flexibility to turn 

the ovens off when not in use. The appliance features three 

settings 

ROAST, GRILL

 & ‘

e

’.

The 

ROAST

 setting (

Fig. 6.3

) is zoned in heat, meaning that 

towards the top it’s slightly hotter than the centre and the 

centre is slightly hotter than the lowest position. It is suitable 

for high temperature cooking, such as roasting, scones, 

baking pastries and bread.
The ‘

e

 setting (

Fig. 6.4

) converts the upper oven to a 

moderate 

BAKING

 oven, ideal for cakes, biscuits and 

anything requiring moderate heat such as fish pie, lasagne, 

soufflés, crumbles and roulades. Meat and poultry can be 

cooked here over longer periods of time. For best results 

when baking cakes; place them in the middle of the oven, 

swap trays if using more than one shelf and allow air 

circulation around trays and tins.
The 

GRILL

 setting (

Fig. 6.5

) utilises the top element in the 

upper oven to provide cooking heat within the cavity. 

THE GRILL DOOR MUST BE KEPT CLOSED WHEN THE GRILL 

IS ON.
1. 

When operating the grill, the cooling fan will also 

operate

2. 

For best results preheat the grill for approximately 2 

minutes from Roasting setting and 5 minutes from ‘e’ 

setting and 10 minutes from cold.

3. 

The grill has 4 shelf positions (see 

Fig. 6.2

), the higher 

positions for fast cooking and the lower settings for 

slowing cooking and browning gratins and pies

CAUTION

: Accessible part may be hot when the grill is in use. 

Young children should be kept away.

PLEASE NOTE

: When the grill is in use the power to the ovens 

is cut. Normal grilling unless for very long periods will not 

affect the heat retention in the ovens.
It is not recommended to cook in the ovens at the same time 

as operating the grill.

FOR THE BEST RESULTS USE THE GRILL FOR A MAXIMUM 

OF 30 MINUTES.

e

Fig. 6.2

 

Fig. 6.3

 

Fig. 6.4

 

Fig. 6.5

 

Summary of Contents for LPRT 517931









































Reviews: