background image

 

7

 

Raveon Technologies Corp. 

 

Pin 4 (Enable)

 is a black wire. Ground to disable product. Connect to Pin 1 or a 

voltage > 2V to enable product, For enable voltages higher than 5V, put a 1K ohm 
resistor in series with it.    

 

2.7.  LED Indicators 

The TechSeries have 3 LEDs on their front panel: 

PWR  Power LED 

The power LED blinks green every two seconds. To conserve energy, the blink is a 
very short amount of time.  If you look carefully at the PWR led, you will see the 
periodic green flicker of light when the product is powered on.   

STAT LED 

The status LED indicates the status of the transmitter, receiver, and GPS.   

Green:

   

The receiver is receiving data over the air, or the channel is busy.  

Red:

   

The transmitter is transmitting data.  

Orange:

    The GPS receiver in the product has not yet locked to the GPS satellites.  

 

LINK LED 

The LINK led is used on DART systems where the radio modem connects to a secure 
network, and the LINK LED indicates the status. If the Dart system is not used, the link 
LED will remain off.   

Connected:

   

The device is authenticated and can communicate on the network.  

Red:

   

The device is denied access to the network. 

Off:

 

The system does not use the LINK LED, or the user disabled it.   

 

   

3.  Tech Series I/O Interface Information 

Products that are compatible with the Tech Series enclosure usually have an I/O mode 
command to configure them for auto-detect of Tech Series I/O interfaces.  ATIO is the 
command.  ATIO 8 sets the product to search the Tech Series front panel for 
information about which panel is plugged into it.   

3.1.  RS-232    [ S ] 

5T835 

The RS-232 9-pin serial I/O connector is a female 9-pin D-subminiature connector 
having the following pins configuration.  It is pinned out so that it may be plugged 
direct

ly into a computer or PC’s 9-pin COM port.   

Summary of Contents for Tech Series






















Reviews: