background image

RV-M50-E Technical Manual

 

 

16

 

modem into Command mode, as well as set the serial port to 9600 baud, 8 data bits, one stop, and no 
parity.  If the baud-rate was OK, verify the AT, BT and CT times, that they are long enough for you to 
enter the +++ string.  

Solution #2: Handshaking.  You may have hardware handshaking enabled on your terminal program, but 
the hardware or cable may not support it.  Disable hardware handshaking on your terminal program to 
verify this is the issue.    

Solution #3: Deep Sleep.  If the TXRATE is greater than 60 seconds, the unit may be put into a very deep 
sleep mode, and will not enter the command mode.  You must first turn the unit off, and back on to put 
it into Command mode. 

6.

 

Mechanical 

  

7.

 

NOTICE 

There are no user-serviceable points inside this transceiver. All service work must be referred to your 
Authorized Service Center or Raveon Technologies Service Department.  

7.1.

 

Safety Training information 

Always use this radio with the antenna supplied with it. This radio is restricted to occupational use. 
Work related operations are permitted only when the radio operator has the knowledge to control the 
exposure conditions of its passengers and bystanders by maintaining the minimum separation distance. 
Failure to observe these restrictions may result in exceeding the FCC RF exposure limits. 

8.

 

FCC Compliance Information 

This device complies with part 15 of the FCC Rules.  Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 

Summary of Contents for RV-M50


















Reviews: