manualshive.com logo in svg

Raveon FireLine Ethernet, Technical Manual, Page: 7 / 34

Share
Download
Raveon FireLine Ethernet Technical Manual Download Page 7

Front Panel 

The front panel of the FireLine modem has these features: 

1.  BNC RF connector 

2.  Transmit LED (TX) 

3.  Receive LED (RX) 

4.  Power LED (PWR)  

5.  9-Pin serial I/O connector 

6.  DC Power Jack 

LEDs 

The three status LEDs visually show the current status of the radio. 

Transmit LED (TX)  

 This LED blinks red when the transmitter keys and is 

putting out RF power.  

Receive LED (RX)

   This LED glows red when there is an RF signal on the 

radio’s receive frequency. This LED will indicate the presence of any signal, 
even one from other sources or radios, data, or voice.  If it glows steadily at 
all times, there is probably some other user on the radio channel.  

Power LED (PWR) 

  This has a short blink, once every two seconds, 

indicating to the user that the power to the modem is ON and the modem is 
working.  When the modem is in the command mode, this LED will blink on 
and off, once per second.  In the normal operating mode, this led will also 
glow red when data is received over the air.   

DC Power 

DC power for the modem is connected to the 2-pin DC power input jack 
labeled 

DC IN

.   

Its connection is optional, as the user may alternately apply power to Pin 9 
and ground to pin 5 of the 9-pin I/O connector,. 

Summary of Contents for FireLine Ethernet



































Reviews:

No comments