manualshive.com logo in svg

Raven Sidekick Pro ISO, Installation & Operation Manual

Share
Download
Raven Sidekick Pro ISO Installation & Operation Manual Download Page 17

CHAPTER

3

P/N 016-0171-509 Rev. E

13

CHAPTER 3

INSTALLATION

OVERVIEW

The following steps must be completed to install a Sidekick Pro™ ISO injection system:
1. Select and plumb the point of injection. See page 14.

a. Install carrier and chemical injection check valves.
b. Install in-line mixer.

2. Mount the Sidekick Pro ISO injection module or tank. See page 20.
3. Mount the Sidekick Pro ISO injection pump. See page 20.
4. Plumb the Sidekick Pro ISO pump and injection lines into the main carrier line at point of injection. See 

page 22.

5. Install the closed calibration system. See page 23.
6. Plumb the recommended rinse system. See page 24.
7. Connect the Sidekick Pro ISO injection pump to CANbus. See page 26.
8. Connect the Sidekick Pro ISO pump to source of electrical power. See page 26.

The following sections provide detailed information and procedure to assist with completing the above steps. 

Contact a local Raven dealer for assistance or questions during the installation procedure.

FIGURE 1. Example Sidekick Pro™ ISO Injection System 

Summary of Contents for Sidekick Pro ISO



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands